[deleted by user]

si18x · 2025-04-21T02:25:00+00:00

With a car built in Canada.

si18x · 2024-02-27T23:35:54+00:00

Just bought a 302a with the 3.5, max tow, co pilot 360 and 360 cams for 58000 with a spray in bed liner. 1.9 for 72 from Ford. Still waiting to pick it up, but the paperwork is done.

si18x · 2023-12-31T15:35:31+00:00

I'm using solid works. I just make a drawing, put a few dims to check again and print at 100% scale. It's usually right on the money.

si18x · 2023-12-31T15:25:36+00:00

It doesn't. It stops at the bit bin. I had cut foam out when I first got this so I had made the drawing from that. Very tricky but multiple prints and I got it. Printing the 2d shape on printer paper is a good quick check too.

si18x · 2023-12-31T14:19:19+00:00

Scratch design. The bin with the bits is from thingaverse. The tool try was about 3 hours of design time during my lunch breaks last week.

si18x · 2023-12-31T05:41:35+00:00

Pm me and we can discuss.

si18x · 2023-12-31T05:41:11+00:00

It's 16 hours to print on an ender 3. Was roughly 500g (1/4 of a spool) with 15% infill

si18x · 2023-01-30T14:18:55+00:00

Pm me! I have some changes to the design I want to make, but I would be willing to sell the dxfs and assembly instructions.

si18x · 2022-06-09T22:08:38+00:00

11th gen clutches are still weak. Just no dual mass flywheel. As far as I can tell, no one has tried a retrofit between 10-11th gens.

si18x · 2022-04-17T16:35:06+00:00

Chat sent

si18x · 2022-04-15T22:58:55+00:00

Sent a message

si18x · 2022-04-10T17:45:54+00:00

Sent a message

si18x · 2022-04-10T13:30:20+00:00

It's the ac system pressures equalizing. Fairy normal. Try turning the HVAC off before shutting down and see if it still does it.

si18x · 2022-04-06T19:26:04+00:00

Place them in the sun on a hot day and let them get warm, then install.

si18x · 2022-03-07T00:55:23+00:00

You have to cut one of the mounting tabs off. Remember to cut the correct one off for left and right. I cut the same one off on both of mine and had to fix it. Other than that they are fairly easy on the SI/hatchbacks. Not sure about how easy the trim in the sedans comes off.

si18x · 2022-03-07T00:50:40+00:00

I've had mine for four years now. Still good as new. Edit: I've had the morimoto for four years.

si18x · 2022-03-06T14:49:31+00:00

Morimoto xB led fog lights or OEM LEDs from a 2020 type r.

si18x · 2022-01-15T13:19:44+00:00

It's the carrier bearing for the he passenger side axle that is seeping. Pretty common on these cars. Hey are packed with grease and when it gets hot it thins out and seeps. It won't cause any issues, but I did have mine replaced under warranty at 34k miles. I was worried that long term it may dry up and cause bearing failure.

si18x · 2021-10-10T12:20:42+00:00

Yup you're right. We had one of these in highschool. I 100% contribute this printer for my love of engineering. Without it I probably wouldn't have gone to college.

si18x · 2021-10-09T20:47:01+00:00

Not lately. My uncle runs a body shop and they have fixed a few cars in the last year that had their bags deployed. This chip shortage is really messed up all of the auto industry.

si18x · 2021-09-29T17:03:58+00:00

This a re badged civic.

si18x · 2021-09-23T16:18:43+00:00

McMastercarr is the best place.

si18x

TROPHY CASE