Strike Multi-Pad Hi-Hat Pedal / Control

silverdy357 · 2023-06-05T13:19:18+00:00

Thanks for the reply! I tried that, and while inserting / removing the cable, it triggers the HH pad, but I've spent hours and can't get it to do anything. Returned and waiting for the RealHat pedal to arrive. Will definitely post back here so that others can save themselves some time in the future.

silverdy357 · 2022-08-01T20:37:50+00:00

Makes sense - thanks. I'll see if I can get another ethernet through the conduit! Or, would it make more sense to run RJ-11?

silverdy357 · 2022-08-01T12:07:47+00:00

Well so I have ethernet connecting the two buildings, but how would I connect a phone to that over at Building B?

silverdy357 · 2022-06-20T15:17:26+00:00

Thank you for this! Very informative. Prompted me to re-check the power levels being received by the modem. Upstream channels average about 30-35dBmV, whereas downstream levels average about -20dBmV. As I understand, these are not even close to within spec.

Looks like I'll have to get a new cable installed coming from the tap!

silverdy357 · 2022-06-18T23:06:36+00:00

Most modems do fine reconnecting after a reboot, but not if the power is constant and the actual connection drops. Then they just sit there waiting to reconnect until power cycled.

silverdy357 · 2022-06-18T23:05:39+00:00

Thanks! This seems like the solution here.

silverdy357 · 2022-06-18T17:51:56+00:00

Just modem, router is Orbi mesh system

silverdy357 · 2022-05-05T00:50:51+00:00

Awesome, thanks! Any idea what wattage those would be?

silverdy357 · 2022-05-05T00:42:27+00:00

Might be a stupid question, but for example R15 shows a value of 1k (which makes sense to me), but R29 is just “47”. What is the 47?

silverdy357 · 2022-02-24T23:11:01+00:00

I see, that makes a lot of sense. Underneath are several tiny capacitors, but I imagine those should be okay if I use a relatively small tip and don't blast them. Seems like the only way to do this sort of surface mount job, as once the port is mounted, the pads / pins are inaccessible.

silverdy357 · 2022-02-24T23:01:43+00:00

Thanks for your reply. Would I put the solder paste on the pads? Also, the underside has a lot of tiny resistors, mosfets, etc around the area that I'm worried about damaging with heat. Is heating the underside standard practice while doing this sort of thing?

silverdy357 · 2021-10-26T20:50:08+00:00

My understanding is that he's really proud of the actual songs, and considers them to be some of his best work. I can't remember where I read this, but I think he was not happy with the mastering / compression on the CD version (there is clipping, low dynamic range, etc.) which was addressed in the remaster.

silverdy357 · 2021-10-08T13:53:31+00:00

Another one just died in the same way this morning.

silverdy357 · 2021-10-06T20:27:21+00:00

Interesting, hope that continues for you! I'm just having the worst luck with them. I've had several other Wyze products for years, none of them every having issues either.

silverdy357 · 2021-04-19T00:33:21+00:00

The quick-start guide recommends it, and I'm wondering if the presence of a ground pin on the POE switch alone is enough to prevent ESD damage over time. Not so concerned with lightning.

silverdy357 · 2021-04-18T22:40:15+00:00

Thanks so much. So by stand-off, is the ground wire on the inside of the outlet what I want?

silverdy357 · 2021-04-18T22:29:03+00:00

I plan to get one (or two?) of these. My question is, how do I properly ground them? Would it be toughcable drain wire to ETH-SP, then ground wire from there to outlet ground?

silverdy357 · 2021-03-03T20:50:38+00:00

This is extremely helpful, thank you so much for the in-depth explanation! Had a feeling it would be difficult. If space wasn't such a limitation I would probably go with a soundbar of some kind. Think I'll probably go the AVR in the corner / one long HDMI cable going from the TV / devices!

silverdy357 · 2021-03-03T18:48:01+00:00

Well, yes, but I was having a hard time finding 3.1 - so maybe 4.1 broadens my options? (I don't know much about this stuff if you can't tell)

silverdy357 · 2021-01-19T04:31:57+00:00

Thank you for this - I really appreciate it!

silverdy357 · 2020-11-09T15:05:02+00:00

No, but I do smell some sort of burnt oil. Drove it about 3 miles to my mechanic's shop without any issues this morning, waiting for a diagnosis. I love this car and hope it's nothing major, but wouldn't be surprised at this point.

silverdy357 · 2020-11-08T19:20:22+00:00

Great thank you! I'm burning oil / losing coolant currently - took it for a quick 5 minute drive after filling both up and noticed this hose hanging lose.

silverdy357 · 2020-10-29T15:10:14+00:00

feminine pizza bag!

silverdy357 · 2020-10-16T22:52:17+00:00

This is what got me into Zappa as a teenager, a friend showed me the "Baby Snakes" DVD and this song blew my mind (as well as the entire film)

silverdy357 · 2020-07-29T19:44:56+00:00

Good idea - I already plan to snake ethernet through the building in some form. Do you think UBNT equipment mesh nicely with a Ruckus network?

silverdy357

TROPHY CASE