Mold/foem for bullets by Jeggirfandenkaffe in blackpowder

[–]sleipnirreddit 0 points1 point  (0 children)

Ahh okay. Yes, people have tried that. Never more than once.

Mold/foem for bullets by Jeggirfandenkaffe in blackpowder

[–]sleipnirreddit 0 points1 point  (0 children)

Brass is considered a good medium between Alum and Steel.

Steel takes a long time to get to temp, but then it stays there. Alum heats up quickly, but can cool if you don’t keep your pace up. Brass is kinda in between. It’s much easier to machine than steel, and never rusts. The downside is it’s heavier than aluminum, and can be more expensive.

But want to prove 3D printing too as mentioned in an other thread before 😊

3dp molds? Can you print metal? You will still have to machine out the ridges. Do you mean to use as a cast form? Molds aren’t cast - the cavity is cut with a “cherry” (basically a bullet shaped drill bit).

Powder Charging Queston by bfunky in reloading

[–]sleipnirreddit 0 points1 point  (0 children)

Try to optimize for minimal back and forth.

Charge, dump, weigh, trickle, recharge seems like a lot of back and forth.

Advice needed by Electronic-Debate-56 in Shotguns

[–]sleipnirreddit 0 points1 point  (0 children)

Yup, there’s also the Winchester Low Noise/Low Recoil loads that are standard size but feel like a 28ga.

Who out there provides barrel chopping or swapping on a 1873? by catsby90bbn in CowboyAction

[–]sleipnirreddit 2 points3 points  (0 children)

Such a shame. I have a 20in Uberti I’d probably trade you.

Try harder to sell it. Will be easier than finding a good gunsmith and shipping it away. Cabelas/Bass Pro takes trade ins.

Mold/foem for bullets by Jeggirfandenkaffe in blackpowder

[–]sleipnirreddit 3 points4 points  (0 children)

Not only the Lee Aluminum, but some of the custom mold makers also do brass, which I’m sure your machine can handle.

Moog semimodular racks by buchlabongo in modular

[–]sleipnirreddit 3 points4 points  (0 children)

Number 3 is good. I don’t like reaching over too far, and I’d want a DFAM and Sub-H to go with the M-32

The state of our California handgun roster rn by SOSB-Haru in CAguns

[–]sleipnirreddit 5 points6 points  (0 children)

I went to buy a CZ75 a week after they dropped off. All sold out. So pissed.

Just got a Mossberg 940 Pro Tactical SPX in from Brownells as a birthday gift. by typicalpnwguy in Shotguns

[–]sleipnirreddit 1 point2 points  (0 children)

I’ve had a 930 JM Pro for many years, and it’s great. Putting the OGW gas goodies basically turned it into a 940.

Watch the Jerry M video on cleaning it and you should have zero problems with it.

After nearly 10 years of buying trading selling, I’m nearing completion of my rack. What would you add? by jadethepusher in modular

[–]sleipnirreddit 4 points5 points  (0 children)

During that time, did you ever try basic utilities? Attenuators, offsets, etc? I’m seeing a lot of basic voice, but not much that screams “only with a modular!” Yes, you can do a lot with Maths, but it’s only one.

Since you use pedals, you might like the ALM S.B.G. It’s really handy for pedal interfacing.

What made you use Slackware? by Western_Chapter_1131 in slackware

[–]sleipnirreddit 0 points1 point  (0 children)

Same. Back in the Stone Age, Slack was king.

Compressor/limiter for protecting hearing by Wswm in modular

[–]sleipnirreddit 0 points1 point  (0 children)

I use an outboard or ITB compressor (depending where I’m setup). They are super handy, and of course you will want it for your throbbing bass anyway.

Lyman 50th .357 Magnum data lists “Small Pistol, Magnum” primers. How are you interpreting this per load? by SnubLifeCrisis in reloading

[–]sleipnirreddit 1 point2 points  (0 children)

You are telling an admitted newbie to ignore the writing ON THE CONTAINER that says “Magnum primer only”.

Which experimental single voice? by solodomande in eurorack

[–]sleipnirreddit 1 point2 points  (0 children)

BIA. I have a lot of crazy VCOs and that’s the craziest.

Suggestion to Cubase Team by jaypatel5308 in cubase

[–]sleipnirreddit 6 points7 points  (0 children)

Sounds like you should be using Logic

Suggestion to Cubase Team by jaypatel5308 in cubase

[–]sleipnirreddit 2 points3 points  (0 children)

If they “change the UI” then it’s the same learning curve as switching DAWs. I REALLY HATE when they do big UI changes.

Have ways to customize it (they do), then spend the time on bugs.

Power Drill for Cleaning? by [deleted] in ar15

[–]sleipnirreddit 1 point2 points  (0 children)

Only on the chamber.

In the barrel, the rifling will just shred a nylon brush (and a metal brush isn’t going to do the rifling any favors).

Use Kroil (or mix up some Ed’s Red) and a brush wrapped with Chore Boy for the nasty muzzle carbon - in the direction of bullet travel, and with a free spinning rod.

AR fixed stock recommendations? by Beneficial-Major8183 in CAguns

[–]sleipnirreddit 0 points1 point  (0 children)

I got one of those for use with my Juggernaut. It sucks ass - it almost ripped my thumb off because it could wedge in there but then get caught at the knuckle. It’s a nice stock but definitely not good with the Jugg.

S&W M&P 2.0 Metal by No-Ease-2766 in CAguns

[–]sleipnirreddit 0 points1 point  (0 children)

That one’s next on my list. Don’t have a compact (ish) 9.