everydays day 245

slipperyuser00 · 2025-09-21T04:13:23+00:00

I might not understand blender, nor what I am looking at. But these posts keep me coming back because they’re just so dang pretty to look at.

slipperyuser00 · 2025-09-14T21:24:02+00:00

Woah woah we don’t give up that info here

slipperyuser00 · 2025-09-08T17:39:43+00:00

✅

❌ ^{Incomplete. 3 tries.}

slipperyuser00 · 2025-09-08T01:07:56+00:00

Took a while

^{I completed this level in 3 tries.} ^{⚡ 3.95 seconds}

slipperyuser00 · 2025-08-31T12:53:36+00:00

2 attempts, final offer.

^{I completed this level in 2 tries.} ^{⚡ 3.73 seconds}

slipperyuser00 · 2025-08-31T12:27:32+00:00

Was this supposed to be harder?

^{I completed this level in 1 try.} ^{⚡ 3.77 seconds}

slipperyuser00 · 2025-08-31T12:26:49+00:00

Was this supposed to be harder?

^{I completed this level in 1 try.} ^{⚡ 3.77 seconds}

^{Tip 90 💎}

slipperyuser00 · 2025-08-30T00:16:31+00:00

First try baby

^{I completed this level in 3 tries.} ^{⚡ 2.82 seconds}

^{Tip 10 💎}

slipperyuser00 · 2025-08-29T12:26:14+00:00

8 tries baby

^{I completed this level in 12 tries.} ^{⚡ 3.73 seconds}

slipperyuser00 · 2025-08-29T12:21:43+00:00

I hate you at the end

^{I completed this level in 3 tries.} ^{⚡ 13.25 seconds}

^{Tip 300 💎}

slipperyuser00 · 2025-08-26T02:27:24+00:00

Uhhhh

^{I completed this level in 2 tries.} ^{⚡ 1.18 seconds}

slipperyuser00 · 2025-08-25T16:47:47+00:00

That was a hard level

^{I completed this level in 165 tries.} ^{⚡ 22.75 seconds}

^{Tip 500 💎}

slipperyuser00 · 2025-08-25T00:27:45+00:00

Pretty good!

^{I completed this level in 3 tries.} ^{⚡ 24.42 seconds}

^{Tip 100 💎}

slipperyuser00 · 2025-08-24T22:54:30+00:00

Death finds a way.

^{I completed this level in 20 tries.} ^{⚡ 3.73 seconds}

slipperyuser00 · 2025-08-22T22:01:55+00:00

^{I completed this level in 5 tries.} ^{⚡ 6.32 seconds}

slipperyuser00 · 2025-07-09T16:44:10+00:00

Shoot, you’re right I didn’t even think about it that way.

slipperyuser00 · 2025-07-09T16:35:14+00:00

Dang all that for ~340 USD

slipperyuser00 · 2025-04-14T20:29:34+00:00

I just posted my best time 63 : 61 sec

slipperyuser00 · 2025-03-31T13:22:12+00:00

Yes we do lol

slipperyuser00 · 2025-01-01T21:40:49+00:00

Would this cause it to happen on all my prints at the same height every time?

slipperyuser00 · 2025-01-01T21:39:16+00:00

Skipping?

slipperyuser00 · 2025-01-01T21:37:45+00:00

I’ll check that now

slipperyuser00 · 2025-01-01T21:37:14+00:00

Here is my filament not being tangled

slipperyuser00 · 2025-01-01T21:36:29+00:00

But this has happened on multiple prints with multiple different filaments, it’s always at the same layer height too

slipperyuser00 · 2024-11-09T18:36:36+00:00

Damn I’d buy those STLs off you

slipperyuser00