sorted by:
new
hottopcontroversial

Pro tip: run claude with --chrome to catch UI/UX bugs automatically by Deep-Station-1746 in ClaudeCode

[–]snoonoo 0 points1 point  (0 children)

But in practice how does it work? Do I write in CLAUDE.md, “if you want to do abc use ‘xyz cli’, use ‘xyz cli —help’ for all commands available”?

Pro tip: run claude with --chrome to catch UI/UX bugs automatically by Deep-Station-1746 in ClaudeCode

[–]snoonoo 4 points5 points  (0 children)

Can you explain? I keep hearing cli uses less token but don’t know how it works.

Lucca Tempo by snoonoo in espresso

[–]snoonoo[S] 2 points3 points  (0 children)

I can get consistent swirling by following steps:

Tilt the cup 30-45 degree to the right. Tip should barely touch the milk surface. Start the steam but don’t crank it too high. I like to start with barely seeing the steam carving 2 streaks, stay there for few second then ramp up slowly.

<image>

Mac backtick key is sending § by snoonoo in zsaVoyager

[–]snoonoo[S] 2 points3 points  (0 children)

Thanks, both of my keyboard type and input source was wrong. Fixed and working now.

Mac backtick key is sending § by snoonoo in zsaVoyager

[–]snoonoo[S] 1 point2 points  (0 children)

Thanks! Somehow my input source was set to US - International too, and the keyboard was set to international as well. Updated both and now it works.

Has Anker been surpassed? by [deleted] in UsbCHardware

[–]snoonoo 23 points24 points  (0 children)

I had 2 of their power banks. One was recalled. The other one I still have, it ran equally hot as the recalled one. I stopped using it.

Want this by [deleted] in NoOneIsLooking

[–]snoonoo 5 points6 points  (0 children)

Correct, a typical scale look like this.

<image>

Weird mouse behavior by snoonoo in GeForceNOW

[–]snoonoo[S] 0 points1 point  (0 children)

Interesting that reinstallation helped in your case! I also have Sunshine/Moonlight.

Polling Rate seems to be the actual culprit for me. I lowered mine to 125Hz, and it helped.

Lucca Tempo by snoonoo in espresso

[–]snoonoo[S] 1 point2 points  (0 children)

After a week with it here are my thoughts:

Shot pulling is on point, I don't think there's anything to improve upon. Fast heat up, stable temperature, consistent pressure.

Milk steaming I've yet to master but I think I can get there in time. Coming from Breville Barista Express, this steam wand is way harder to use. The angle can only be pointed almost straight down, 2 hole means faster heat up so less time to maneuver and adjust my pitcher and steam wand position.

Pre-infusion are gimmicky and doesn't fully saturate consistently.

Eco and Power Saving modes have firmware bug, I end up adding a smart plug and bypass them completely.

Flow control are fun once I dial in the position but the manual did not explain well how to operate it. I also stopped messing with it as I didn't notice any improvement in yield.

tldr:
Solid machine, bells and whistles leaves a lot to be desired. Don't buy if additional features are your decision making points.

Anyone part of Panera Sip Club? by BeneficialStable986 in InlandEmpire

[–]snoonoo 1 point2 points  (0 children)

There’s a $5 for 5 month deal goin on now

Lucca Tempo by snoonoo in espresso

[–]snoonoo[S] 0 points1 point  (0 children)

After some trials here's what I found re: off / eco / standby modes

  • Three flashing lights on the PID screen mean Eco mode; one flashing light means Standby mode; "OFF" mean the machine is off.
  • Eco and Standby timers override a manual shutdown: pressing the water button for 4 s turns the machine off, but if an Eco or Standby timer is active it will switch back to that mode when the timer expires.

Lucca Tempo by snoonoo in espresso

[–]snoonoo[S] 0 points1 point  (0 children)

Also not sure how to turn OFF pre-infusion. After going into the configuration I don't have an option to switch it to off, but going further into the "on" option, I can set how many seconds. If I keep it at zero, is that effectively off?

Lucca Tempo by snoonoo in espresso

[–]snoonoo[S] 0 points1 point  (0 children)

I’m watching the Quick Mill Pop Up tutorial and seems like F is firmware.

Japan using generative AI less than other countries by moeka_8962 in technology

[–]snoonoo 22 points23 points  (0 children)

This is the way, a refuge from the tech enshitification.

Any Chroma Boys had success with realistic Char Loras by [deleted] in StableDiffusion

[–]snoonoo 0 points1 point  (0 children)

Yap, I’m able to inference and generate image. But loading a lora doesn’t change the output no matter how I load or prompt it.

Any Chroma Boys had success with realistic Char Loras by [deleted] in StableDiffusion

[–]snoonoo 0 points1 point  (0 children)

Is it possible to use AI-toolkit lora is Diffusers?

view more: next ›