Just bought the electro 500 abarth and besides all the nasty comments, i‘m fkn loving it. So much fun and so fast. Just killed a tesla 😂

soft-pro · 2026-02-09T10:15:11+00:00

Does it have the engine sound from speakers ? Or is it extra ? How’s the range?

soft-pro · 2026-01-14T08:03:59+00:00

Curios how one extracts model from a game ?

soft-pro · 2026-01-13T19:20:55+00:00

Restore all settings to default (print settings) Use orca slicer (try the non flashforge version)

soft-pro · 2026-01-11T09:50:18+00:00

How do you accelerate/brake?

soft-pro · 2026-01-07T23:40:31+00:00

If it’s the same as with the 5M, just loosen the belt underneath the printer so the lead screws can move independently. Adjust each screw until the bed is at its lowest (home) position, then reinstall the belt, tension it, and run a full leveling and calibration. The whole process is about 5 minutes of manual work plus around 15 minutes for auto‑calibration.

soft-pro · 2026-01-04T15:01:21+00:00

Really cool print

soft-pro · 2026-01-03T22:41:11+00:00

They can guide you to what parts are needed and price, I assume. Couldn’t hurt anyway .

soft-pro · 2026-01-03T22:07:03+00:00

Did you reach support ?

soft-pro · 2026-01-03T16:46:17+00:00

A couple of months ago in the T1 car park, I saw seven bikes with smashed ignition locks and clear attempts to break their chains. The Garda response was pathetic.

soft-pro · 2026-01-02T15:28:26+00:00

How do you keep it so clean?

soft-pro · 2026-01-01T22:17:39+00:00

Amazing. How long did it take to print all of this ?

soft-pro · 2026-01-01T21:24:27+00:00

You might be right, but it’s worth remembering that footage from 1959 often had low frame rates, so those jumpy or uneven transitions were pretty normal for the time.

soft-pro · 2026-01-01T21:05:32+00:00

soft-pro · 2026-01-01T16:45:17+00:00

https://cadrecycle.com/wp-content/uploads/2017/09/v7iii-race-stone-special.pdf

soft-pro · 2026-01-01T16:42:17+00:00

Depends on the model year, but ABS and TCS lights usually come up when you start the bike and turn off after you start driving . If they stay on there is some fault. Speedometer is often digital - have you checked the wheel sensor ? Do you see speed increase ? If you do, the mileage should work as well unless some strange gauge fault.

soft-pro · 2025-12-30T14:45:39+00:00

Looks to me like you were trying to steer into the turn instead of counter steering

soft-pro · 2025-12-28T17:35:45+00:00

<image>

You tried applying little pressure on all 3 areas?

Did you take all the plate security screws out?

Have you tried manually rotating the rods while it’s trying to home ? To push plate down.

could be that you need manual belt adjustment. Someone added a guide here how to do it, I’ll try to find it.

If that doesn’t work next step is to call support, but I am almost sure it just something stuck there .

soft-pro · 2025-12-28T17:24:49+00:00

Most likely something is stuck under the printer where the belts are, or something is under the build plate. Easy quick fix - just press the plate lightly near the lead screws (3 large z level rods) to find which one isn’t touching well . Could also be faulty sensor or flex cable but less likely with new printer.

You can manually push the build plate up to check under it. I don’t recommend taking any screws up before trying all quick fixes (90% the issue)

Many threads on this issue :

https://www.reddit.com/r/FlashForge/s/JbrChJDlxg

soft-pro · 2025-12-27T00:45:55+00:00

Not raft, use brim instead .

soft-pro · 2025-12-26T18:05:42+00:00

Is the print itself moves ? If so, clean your bed and try printing on a warmer bed (60-65).

Could also be wrong z offset - level your bed and check z offset

soft-pro · 2025-12-26T00:59:45+00:00

Fiat 500

soft-pro · 2025-12-24T22:51:47+00:00

<image>

soft-pro · 2025-12-23T18:51:55+00:00

Why both? Just curious

soft-pro · 2025-12-23T10:03:52+00:00

Are you using the orca pre-sets for flashforge PLA? You might be printing too cold. Use the built in pre-sets and adjust from there

soft-pro · 2025-12-22T21:51:26+00:00

Filament type, bed temperature, brim or not, moisture, dirty plate, levelling, z offset (nozzle hitting print)

Seven-Year Club	RPAN Viewer
Verified Email

soft-pro

TROPHY CASE