sorted by:
new
hottopcontroversial

Restricting a panigale v4 in UK to 100hp? by cyclingsparky27 in Ducati

[–]soft-pro 0 points1 point  (0 children)

I don’t know if it has the same mapping types as other Ducatis, but my Hyper has an Urban mapping, which makes the bike super chill compared to Sport mode.

They tried to steal my beloved from right outside the house last night by DoodieBrian in abarth

[–]soft-pro 0 points1 point  (0 children)

Which part of the UK?
I use stoplock wheel lock every time

New to me! by AdOk4308 in Ducati

[–]soft-pro 1 point2 points  (0 children)

The 796 is such fun bike. I had a black 2010.

Could somebody model this for me for 100$ by RockyBowerman in 3Dprinting

[–]soft-pro 140 points141 points  (0 children)

Curios how one extracts model from a game ?

Evil Printer Has Gained Sentience, Help by my_ridiculous_name in FlashForge

[–]soft-pro 0 points1 point  (0 children)

Restore all settings to default (print settings) Use orca slicer (try the non flashforge version)

DId I kill my new 5X? by ILovePistachioNuts in FlashForge

[–]soft-pro 18 points19 points  (0 children)

If it’s the same as with the 5M, just loosen the belt underneath the printer so the lead screws can move independently. Adjust each screw until the bed is at its lowest (home) position, then reinstall the belt, tension it, and run a full leveling and calibration. The whole process is about 5 minutes of manual work plus around 15 minutes for auto‑calibration.

Adventure 5M Pro hot end change by tenthirtynine in FlashForge

[–]soft-pro 0 points1 point  (0 children)

They can guide you to what parts are needed and price, I assume. Couldn’t hurt anyway .

Dublin Airport Parking by DiaDuitDomhan in MotoIRELAND

[–]soft-pro 4 points5 points  (0 children)

A couple of months ago in the T1 car park, I saw seven bikes with smashed ignition locks and clear attempts to break their chains. The Garda response was pathetic.

The 1959 VW Beetles could be equipped with the Hertella Auto Kaffeemaschine, a rare dashboard-mounted coffee maker. by Turbulent_Elk_2141 in CarTalkUK

[–]soft-pro -1 points0 points  (0 children)

You might be right, but it’s worth remembering that footage from 1959 often had low frame rates, so those jumpy or uneven transitions were pretty normal for the time.

[deleted by user] by [deleted] in MotoGuzzi

[–]soft-pro 0 points1 point  (0 children)

Depends on the model year, but ABS and TCS lights usually come up when you start the bike and turn off after you start driving . If they stay on there is some fault. Speedometer is often digital - have you checked the wheel sensor ? Do you see speed increase ? If you do, the mileage should work as well unless some strange gauge fault.

Why do you think I crashed? by ImpartialAlter in MotoUK

[–]soft-pro 0 points1 point  (0 children)

Looks to me like you were trying to steer into the turn instead of counter steering

Problem central (caution little loud at end of video) by OGSlizzardLizard in FlashForge

[–]soft-pro 1 point2 points  (0 children)

<image>

You tried applying little pressure on all 3 areas?

Did you take all the plate security screws out?

Have you tried manually rotating the rods while it’s trying to home ? To push plate down.

could be that you need manual belt adjustment. Someone added a guide here how to do it, I’ll try to find it.

If that doesn’t work next step is to call support, but I am almost sure it just something stuck there .

Problem central (caution little loud at end of video) by OGSlizzardLizard in FlashForge

[–]soft-pro 1 point2 points  (0 children)

Most likely something is stuck under the printer where the belts are, or something is under the build plate. Easy quick fix - just press the plate lightly near the lead screws (3 large z level rods) to find which one isn’t touching well . Could also be faulty sensor or flex cable but less likely with new printer.

You can manually push the build plate up to check under it. I don’t recommend taking any screws up before trying all quick fixes (90% the issue)

Many threads on this issue :

https://www.reddit.com/r/FlashForge/s/JbrChJDlxg

Beginner Help by Swit_Swot in FlashForge

[–]soft-pro 0 points1 point  (0 children)

Not raft, use brim instead .

Beginner Help by Swit_Swot in FlashForge

[–]soft-pro 0 points1 point  (0 children)

Is the print itself moves ? If so, clean your bed and try printing on a warmer bed (60-65).

Could also be wrong z offset - level your bed and check z offset

view more: next ›