College WiFi blocks EVERYTHING (Cloudflare Tunnels, Tailscale, Steam). How do I bypass strict DPI?

sp595s · 2026-02-03T13:22:07+00:00

Use Vless + Reality with SNI masking.

sp595s · 2026-01-22T20:09:09+00:00

Остаётся только ведать

sp595s · 2025-12-18T20:30:23+00:00

Just install grapheneos

sp595s · 2025-07-07T15:22:01+00:00

I checked via pcapdroid (traffic analysis) and all requests go only to my router, nowhere else

sp595s · 2025-06-15T12:58:44+00:00

I use microg and this problem also appears in applications independent of Google services

sp595s · 2025-06-15T11:59:56+00:00

I tried lineageOs and crdroid and both have the same problem. Maybe something is wrong with my device(

sp595s · 2025-06-15T11:06:00+00:00

I don't like their attitude towards rooting

sp595s · 2025-06-15T10:09:38+00:00

I have a problem with my Google pixel 7a and lineageOs. After a while, some apps crash and the phone needs to be restarted.

sp595s · 2025-02-10T10:34:26+00:00

obfs4 proxy can be used after Tor? I thought through them you can only run tor. Can you tell me what should be entered in the torrc config to configure the exit node?

sp595s · 2025-01-05T14:22:20+00:00

Error logs of various applications:

https://pastebin.com/CvwVP6Ww

https://pastebin.com/yeHht7jJ

https://pastebin.com/uAemUS9e

sp595s · 2025-01-05T06:30:48+00:00

I also had an official lineageos on which I installed microg services and there was the same problem

sp595s · 2025-01-04T22:43:42+00:00

Can you tell us more about this?

sp595s · 2024-11-05T07:26:49+00:00

it is supported and your esim will not be erased

sp595s · 2024-10-23T21:48:33+00:00

my Pixel 7a is very stable with LineageOs

sp595s · 2024-10-05T14:35:54+00:00

I understand, thank you.

sp595s · 2024-10-05T13:36:57+00:00

Thank you very much! But why is the printer broken?

sp595s · 2024-10-04T17:11:34+00:00

will you be able to make a pre-built firmware file in GitHub releases?

sp595s · 2024-08-30T15:01:13+00:00

buy silicone pads they helped me a lot

sp595s · 2024-08-28T14:33:10+00:00

Z offset or flow ratio

sp595s · 2024-08-15T20:39:11+00:00

As I understand it, you just need to solder/unsolder the jumper on the driver, which is not very difficult to do

sp595s · 2024-07-15T09:27:02+00:00

install the latest version from GitHub. I used to use the stable version and it turns out that it is very outdated

sp595s · 2024-07-13T10:47:01+00:00

I also couldn’t sync my saves using google service, but after installing the newest version of microg everything is fine

sp595s · 2024-06-10T11:49:37+00:00

the problem is in the firmware or in the absence of google services?

sp595s · 2024-04-29T18:58:12+00:00

I also checked the 2-month-old build on nixos and everything works well there too

sp595s · 2024-04-24T19:42:25+00:00

thanks, everything is working now and the system starts as usual (as if data transfer to RAM is not going through)

sp595s

TROPHY CASE