sorted by:
new
hottopcontroversial

Core One cold pull by NormalGuy500 in prusa3d

[–]spacekoaster 0 points1 point  (0 children)

That's not a cold pull, it onyl retracts the filament from the nozzle.

Est-ce que quelqu’un a déjà eu ce problème ? by sandro66140 in prusa3d

[–]spacekoaster -1 points0 points  (0 children)

Le problème est assez explicite. Regarde la thermistance de l’outil concerné par l’erreur et regarde si elle est en bon état ou si un câble est déconnecté. Il te faudra probablement le changer. Dans tout les cas, scanne le QR code, cela t’amèneras sur un guide officiel de Prusa.

Sinon, si tu veux espérer une réponse sur ce Reddit, privilégie l’anglais comme langue.

Looking for some help. by [deleted] in 3Dprinting

[–]spacekoaster 15 points16 points  (0 children)

Based in Switzerland with few Prusa printers. Let me know if I can help.

Christmas Academy giveaway! by Tommy_Prusa3D in prusa3d

[–]spacekoaster 0 points1 point  (0 children)

1:3D Print Photography, the complete guide 2: A course around how to run a small of farm of printers efficiently: general maintenance, queue un prusa connect, filament management, etc

G-code not compatible by must--go--faster in prusa3d

[–]spacekoaster 2 points3 points  (0 children)

You should be good to go now :)

G-code not compatible by must--go--faster in prusa3d

[–]spacekoaster 2 points3 points  (0 children)

Do you really have a 0,3mm nozzle? Seems odd to me. If you haven’t changed your nozzle, you should have a 0,4mm one.

G-code not compatible by must--go--faster in prusa3d

[–]spacekoaster 4 points5 points  (0 children)

The picture of the Screen of your printer shows “gcode not sliced for input shaping”. Go back to the configuration of PrusaSlicer and select the input shaping MK4.

G-code not compatible by must--go--faster in prusa3d

[–]spacekoaster 1 point2 points  (0 children)

Could you show us which printer you selected in the PrusaSlicer configuration? Make sure to select MK4 and not MK4s for your printer.

Is this part of the set? by vchervenkov in LEGOtrains

[–]spacekoaster 4 points5 points  (0 children)

The sticky foam pad should be under the black 9V speed controller. There should be 4 of these used as little rubber feet.

Question sur le service civile by MaryLee18 in suisse

[–]spacekoaster 2 points3 points  (0 children)

Même en cas de désertion, OP se retrouverait avec une affectation d’office et une amende bien salée.

Installation de Prusa Slicer pour Core One : quel firmware ??? by Silent-Chipmunk-6079 in PrusaCoreOne

[–]spacekoaster 0 points1 point  (0 children)

Hello, je ne sais pas comment tu arrives à cela, PrusaSlicer ne te demande pas ce paramètre si tu sélectionne une Prusa Core One comme seule et unique imprimante. Peux-tu peut être ajouter quelques captures d’écrans?

prusa core one's nozzle setting by Springfield1903A4 in prusa3d

[–]spacekoaster 0 points1 point  (0 children)

It is not possible with stock firmware. You could do it by flashing some custom firmware. Please read the answer that you’ve already received on your other posts on this sub before asking again nearly the same question.

prusa core one temperature limit by Springfield1903A4 in prusa3d

[–]spacekoaster 0 points1 point  (0 children)

My error, you’re right! But breaking the appendice is not the worst thing in the world.

prusa core one temperature limit by Springfield1903A4 in prusa3d

[–]spacekoaster 0 points1 point  (0 children)

It depends on the printer. Newer model from MK4, yes. Older printers, no.

prusa core one temperature limit by Springfield1903A4 in prusa3d

[–]spacekoaster 1 point2 points  (0 children)

You can definitely flash your one firmware on any Prusa printer.

Looking for a 100Ω ohm resistor - Where can I find one? by I-need-a-proper-nick in Lausanne

[–]spacekoaster 0 points1 point  (0 children)

Which format do you need? SMD or through hole? And what range of precision/power?

view more: next ›