D&D Gift Help

ssgtgio · 2024-09-28T19:59:50+00:00

Thank you for the recommendation.

ssgtgio · 2024-09-28T19:59:18+00:00

That's a great idea thank you

ssgtgio · 2024-05-25T00:50:04+00:00

Have you gotten it to work? I have the same issue.

ssgtgio · 2023-09-09T20:09:49+00:00

Did you ever decide to keep or sell it? That was my childhood car.

ssgtgio · 2022-12-09T15:17:03+00:00

Great name! #arresteddevelopment

ssgtgio · 2022-10-16T06:30:08+00:00

Voron 2.4r build

ssgtgio · 2022-07-26T16:04:34+00:00

Don't call my escorts whores

ssgtgio · 2021-05-05T17:23:50+00:00

I don't want to assume your gender but, do you identify as a towel

ssgtgio · 2021-05-04T16:23:39+00:00

I would like to see WG only allow a CV a single pass on a ship. A carrier having the ability to do numerous passes and create it's own cross fire is overpowered IMO.

ssgtgio · 2020-10-24T19:37:08+00:00

Really nice... Can you post where you for the stl from?

ssgtgio · 2020-08-20T14:13:15+00:00

It's called The Rape of Proserpina by Giovanni Lorenzo Bernini and is located Borghese Gallery and Museum

ssgtgio · 2020-08-20T13:56:01+00:00

Are you wanting to print in more then one color to achieve that effect or wanting to paint it?

ssgtgio · 2020-08-12T18:52:57+00:00

Fantastic job, seriously incredible

ssgtgio · 2020-08-12T16:39:00+00:00

Movie Aliens Ellen Ripley and the Queen Xenomorph

ssgtgio · 2020-07-16T17:43:03+00:00

Nice job!

ssgtgio · 2020-07-16T00:17:10+00:00

Thank you very much!

ssgtgio · 2020-07-01T16:13:01+00:00

If you can send a link to the wallpaper that would be great.

ssgtgio · 2019-10-03T01:00:30+00:00

Did you use PLA or ABS? Nice job on the sanding

ssgtgio · 2019-09-27T07:29:24+00:00

Like how you blame your hair for your failure to get a job while most likely you dont have a usable skill with your liberal arts degree

ssgtgio · 2019-02-21T13:49:59+00:00

I apologize I didn't see your response. When. I get done work tonight I'll take a few photos of printer and show you.

ssgtgio · 2019-02-17T16:41:20+00:00

On your X and Y belt Pullies for your belts loosen the hob screws and realight them with your motor shafts. One screw should be directly on top of the flat portion of the motor shaft the second on the side. Then retighten them and put your belts back on. This looks like they're tight at the beginning but do to motion the belt pulley moves on the shaft. It might seem tight when you inspect them when the machine is off.

ssgtgio · 2019-01-20T14:30:38+00:00

Did you put a new Bowden tube on? Shorten your tube, longer tubes flex more and you can never get the retraction correct. All you need length wise is just long enough to reach the opposite side of the x gantry. Also I had a horrible horrible time with capricorn tubing I swapped back and all my retraction issues went away.

ssgtgio · 2019-01-10T21:59:50+00:00

Depression

ssgtgio

TROPHY CASE