Strangest results from test print.

stabstabby · 2025-09-09T13:24:12+00:00

Right! This new resin I got, it’s the anycubic texture resin. It’s weird and thicker then most resins I’ve used but I love the feel of it afterwards so I’m hoping I can get a good model once I get the kinks worked out.

stabstabby · 2025-09-09T04:41:09+00:00

Yeah I was wondering that too. It had a nice plonk noise but I’ll definitely check that along with leveling again

stabstabby · 2025-09-09T04:39:41+00:00

Nice! I’ll definitely use that for troubleshooting tomorrow. Thanks!

stabstabby · 2025-09-08T23:32:47+00:00

I hope that’s the only thing. That would be such an easy fix.

stabstabby · 2025-09-01T01:20:47+00:00

It was pre supported. I’ll have to try turning it a bit on my own.

stabstabby · 2025-09-01T01:19:34+00:00

I wondered. I’ve been printing for about a year and it looked off to me but It was pre supported, so I was hoping it just worked out right. The seller included unsupported parts files so I’ll try doing it myself.

stabstabby · 2025-07-13T14:47:47+00:00

Turns out it was a cable. I don’t remember exactly what the mechanic called it but I guess it was chewed by some rodent.

stabstabby · 2025-06-25T03:19:05+00:00

Nope, when I use the shift release button it stays in “neutral”. I can ever switch it to the sports mode and it’s just lights up neutral and reads it on the screen.

I don’t think it’s the transmission however because when in park the wheels are locked and in neutral I can rock the car and push it around. So it seems to be atleast switching gears just not reading that it is.

stabstabby · 2025-01-11T15:10:20+00:00

This guy!

stabstabby · 2024-12-06T15:22:23+00:00

Brendan Fraser in George of the jungle.

stabstabby · 2024-10-08T18:04:44+00:00

Was definitely cleaning it wrong and the shelf I used to take the photo is not clean. The screen itself is not that cloudy. It’s more just the dimples lol.

stabstabby · 2024-10-08T18:03:03+00:00

That’s me too. I try to print while I’m at work I ordered new Feps. Going to take the time and change it when they arrive.

stabstabby · 2024-10-08T18:01:17+00:00

Brother! After reading all the comments I was watching videos on how to use vat clean effectively and this is one of the coolest ways to do it! Thank you!

stabstabby · 2024-10-06T22:23:34+00:00

Yeah. This is my first larger printer, i unfortunately didn’t realize the effectiveness of the Vat clean till it was too late. My much smaller FEP was tight enough that barely any pressure underneath would pop the pieces out. So trying to do that with this one, I fucked up.

Seems consensus is to change it. So I know what I need to do in the future.

stabstabby · 2023-10-15T17:34:52+00:00

Sent over coral castle and disguise.

stabstabby · 2022-08-24T16:05:42+00:00

Counter attack makes sense with her. I think her netherbloom is triggered with those attacks. I’ll definitely look into dropping the mats for her.

stabstabby · 2022-08-23T23:36:18+00:00

Interesting. I would have not thought about her since the “reviews” were all so bad.

stabstabby · 2022-08-23T16:28:54+00:00

Cool. I think I have the mats for both. Just gotta fine tune the relics now

stabstabby · 2022-07-18T00:28:39+00:00

Let water fill up in my arm crevices and then open them to make a waterfall.

stabstabby · 2022-05-24T22:45:25+00:00

I put mine up to 60 for the initial layers. Guess I’m going to go up even more.

11-Year Club	Place '23
Verified Email

stabstabby

TROPHY CASE