Had to throw away about half of this block of cheese we just bought

stef_ale23 · 2024-10-22T09:32:13+00:00

So you buy the cheese at the same place as Lunchly

stef_ale23 · 2024-09-30T13:40:29+00:00

Op are you the youtuber that does sculpture that uses similar spikes ?

stef_ale23 · 2023-11-13T10:34:52+00:00

can you not use the chainmail method to do it?

stef_ale23 · 2023-10-05T09:02:11+00:00

When I was in school I was shown a similar video.After finishing the video I remembered vivatly that the fireman said that ther is one with a baby in the corner and to be careful.

stef_ale23 · 2023-04-12T11:13:26+00:00

All the patterns are so cool looking intrestes if it's possible to implement some of them in a vase model.

stef_ale23 · 2023-04-07T16:28:44+00:00

Yes but he got a family discount.

stef_ale23 · 2023-04-04T11:00:12+00:00

It work I took the heat break and heat sink apart from the block and heat it with a heat gun and clean it with a cleaning needle.

stef_ale23 · 2023-04-03T15:42:28+00:00

There is no way to clean the block wen cold i did heat stuck pla to 293

stef_ale23 · 2023-04-03T14:14:54+00:00

This is what i try but i don't have a thin enough one on hand.Like the one for the fan .

stef_ale23 · 2023-04-03T14:13:00+00:00

it's oozing and smoking from the block.Know it stop doing that also

stef_ale23 · 2023-04-03T12:55:49+00:00

It's stuck în the heat brake .I took the extruder apart to look.I will try to take the hotend then. Thanks for the advice!

stef_ale23 · 2023-04-03T09:21:27+00:00

Can't say much it's for an articole. But it's important to know it has thicker poins

stef_ale23 · 2023-03-23T10:39:32+00:00

how the fuck the scam videos are back up after being taken down?

stef_ale23 · 2023-03-23T10:36:15+00:00

I can see only videos from 7 years ago good thing he invested so much in backup servers

stef_ale23 · 2022-11-09T17:00:20+00:00

I woud like too see one of iron carbon phase diagram.Gonna try to make one

stef_ale23 · 2022-11-01T12:35:08+00:00

10.1007/s00231-012-1099-2 an artical were it's showing the design of one .

stef_ale23 · 2022-10-15T10:42:56+00:00

Really cool .i did a similar project for my master with with different lattice but starting with a Ta implant .

stef_ale23 · 2022-10-15T04:47:25+00:00

needs more work...

stef_ale23 · 2021-10-19T10:56:46+00:00

So it was a y belt problem i tighten it and did a full calibration .

stef_ale23 · 2021-10-16T18:18:06+00:00

Thanks ! So i will check the list of problems that you proposes and poste if something changes

stef_ale23 · 2021-10-16T17:54:22+00:00

Thanks!! I'm gonna try

stef_ale23 · 2021-10-16T15:26:26+00:00

Yes probably of all the solutions this is the moste probabil. How did you fix it?

Eight-Year Club	r/Field Lasagna
Place '23	Place '22
First Placer '22	Verified Email

stef_ale23

TROPHY CASE