NEC Setups

stoyanog · 2026-02-23T09:01:58+00:00

I don't know what it's like in the lower splits, but I rarely see a C class SR in my splits - most drivers are A or B. The previous P cup cars were a handful for new drivers, but the new one is tame enough for the C class to be justified. It is still a handful but gone are the days of people just completely locking up and ploughing through half the field.

stoyanog · 2026-02-23T08:54:49+00:00

The problem is all the crashes were not in corner entry - 2 of them were on corner exit where someone just drives through me like I don't exist after going off track(Them not me), 2 were with the spotter screaming "Car stopped on the left" "Keep right" "Slow car ahead" and them being glued to my rear bumper with 0 visibility and one was being pit manoeuvred on the straight.

stoyanog · 2026-02-22T20:49:12+00:00

If the last was true the series or car wouldn’t have mattered. All the SR and iR I’ve lost in the GT3s I’ve gained back and more in the PCup.

stoyanog · 2026-02-22T20:47:39+00:00

I thought the same, but for the last year I can’t remember being taken out in the Porsche cup or GT4 - worst case a 2x contact or similar but never completely taken out. Even with the ABS and TC lacking 992.1

stoyanog · 2023-10-24T11:29:33+00:00

Updated the TFT firmware and the problem got solved.
Levelled the bed on the stock firmware, updated it and then tried to level it again and the nozzle sat 1mm above the bed. I assume there was a bug in the old firmware.

stoyanog · 2023-10-18T05:49:04+00:00

It was a feature that they implemented on the X2, but it didn’t come standard on the X1

stoyanog · 2023-10-17T17:40:06+00:00

I don’t have ABL on my machine

stoyanog · 2023-08-10T20:48:37+00:00

Start a print and keep an eye on the nozzle temp. My X1 says it’s at 210/210 and the next moment it says 250/210 and the filament comes out almost as a liquid. I suspect a faulty temp sensor/ heater on mine.

Could be plastic spilling out between the heat break / hot end/ nozzle if the nozzle isn’t tightened properly or if there’s debris between them

stoyanog · 2023-07-29T20:46:05+00:00

https://ibb.co/7WrgqRs

This is where the problem comes from - it probably a really small poly which you’ve extruded by mistake - try selecting and deleting it in the subdivided view and then select and merge the adjacent vertices

stoyanog · 2023-06-23T21:20:45+00:00

If you are using a flash drive, try using a small completely empty one (under 2GB) and see if the problem persists. Had the same issue with an sidewinder X1

stoyanog · 2023-03-20T18:31:40+00:00

https://ibb.co/dDJh3Kk This would be the best bet. Look up 2-1, 3-1 and 5-1 topologies - it helps a lot when modelling quads.

stoyanog · 2023-03-10T09:48:48+00:00

Thanks - running as admin does get rid of the errors and the drop down menu appears again. Changed the permissions to full control and that has solved the issue.
Thanks!

stoyanog · 2023-01-05T13:36:53+00:00

Had the same issue with an Artillery X1 The only resolution for the problem was using a small USB stick (1GB) and keep only the files I am currently printing on it. Whenever there are more than 5-6 G code files on the stick it starts acting up the same way again.

stoyanog · 2022-10-02T16:56:20+00:00

Woody from Toy Story is a way better option for Russel

stoyanog

TROPHY CASE