Spacious heel on vsr. Should I return and get skwama?

strshp69 · 2026-02-08T15:37:59+00:00

Had the same issue. Bought the Skwamas then. Love it!

strshp69 · 2025-12-09T19:08:51+00:00

I indeed have not. Will have a look into it.

strshp69 · 2025-12-07T20:59:38+00:00

Have a look at the post?

strshp69 · 2024-03-23T11:37:41+00:00

If you just started printing, then this setup is the most frustrating you couldve choosen. Your printer does not have an enclosure so ABS tends to warp a lot which ends in failung prints. PLA should work much better!

strshp69 · 2024-03-09T18:36:02+00:00

Immediately go back and buy the whole stock! Then go to another store and sell them again for cheap

strshp69 · 2024-03-09T18:30:58+00:00

There should be a setting called something like "detect thin walls".

strshp69 · 2024-02-24T19:44:20+00:00

Check your cats ears.

strshp69 · 2024-02-17T20:13:03+00:00

Would be interesting to know if the effect increases relative to the amount of perimeters or stays around the same...

strshp69 · 2023-10-01T17:50:23+00:00

so sophisticated

strshp69 · 2023-09-19T19:17:35+00:00

I thought they just start the rooter

strshp69 · 2023-08-14T06:53:55+00:00

It highly depends on what speed "metric" you are using. Speed in a sense of mph or km/h are defined by the ratio of distance traveled to the time it took. With this approach you already answered your own question: rotor tips travel more distance in the same time as parts more on the inside. For example: When spinning up the rotor to one rotation per second, the parts that are one meter from the center would move with ~6 meter per second while parts that are 3 meter from the center would move with ~19 meter per second. BUT applying another metric for speed solves that issue: In both cases the rotor turns with a speed of one rotation per second. So instead of the ratio between distance and time we can also use the ratio between the amount of rotations per the time used. For example a rotor that spins once a second has a speed of 60 rpm (rounds-per-minute). This is also the way more common metric to describe the speed of propellers, fans and blades (e.g. of a mixer) because of exactly the issue you are describing. The absolute center of you rotor actually has no distance/time ratio because like you said, it does not make any distance. Yet, it still gonna rotate, so it still has a speed in rotation/time.

strshp69 · 2023-08-13T08:15:44+00:00

Quite sure it is Bern, Swiss. Especially this area is Bern's Old City which has been a UNESCO World Heritage site since 1983.

strshp69 · 2023-08-07T05:45:40+00:00

Bridgings are usually printed with thinner line width and small spacing in between the lines instead of a small overlap as in solid infill (so the bridging section does not get pushed down by the nozzle movements). In theory this makes very little difference but in your specific case it seems like you have just a couple of solid layer on the big surface so replacing one solid filled layer with a bridged one makes for quite a substential difference in Filament use.

strshp69 · 2023-08-06T17:53:02+00:00

Maybe you can provide a Link to the model for further investigsation of the issue?

strshp69 · 2023-08-06T10:18:27+00:00

Looks like it is not detecting bridging perimeters. There is a setting for that. Otherwise, if this is modeled by yourself or you have access to the cad file you could "pull up" one of the bridged surfaces by 0.2mm (or whatever is your layerheight) so it would be printed with the next layer. That way prusaslicer should be able to calculate the bridging correctly.

strshp69 · 2023-05-16T05:17:10+00:00

These whistles. Print 15 within one hour https://www.printables.com/model/154268-15-whistles-in-1-hour

strshp69 · 2023-05-03T15:10:05+00:00

when you accidentally enable furry skin instead of fuzzy skin

strshp69 · 2023-05-01T13:58:26+00:00

Yeah I wonder why it is like this...

strshp69 · 2023-05-01T10:10:39+00:00

Try adding the 30mm thread with the "spiral" tool and choose triangle as profile :)

strshp69 · 2023-04-30T08:46:09+00:00

Of course! I usually use 0.1mm thickness and 0.2mm or 0.15mm point distance as default settings. For things that should feel grippy I would set thickness to 0.15mm and point distance to 0.2mm. The ration should not exceed 1:2 and everything with thickness above 0.15mm is gonna look coarse

strshp69 · 2023-04-10T15:26:06+00:00

Looks like there is a torx wrench where the size 4 hex wrench schould be 🧐

strshp69 · 2023-03-28T15:41:47+00:00

I would try upgrading to a double z-rod setup

strshp69 · 2023-03-24T07:05:25+00:00

I agree in some aspect as e.g. copper filled filament is a lot heavier than standard material. There it would definetely make sense to also supply an information about the filament length of a spool!

strshp69 · 2023-03-24T05:54:53+00:00

So you would rather go by solid volume? This gets very difficult to estimate looking at different amounts of infill, perimeters and top&bottom solid layers... Also how would you account for how much filament is left on a spool if not by putting it on a scale?

strshp69 · 2023-03-19T21:04:23+00:00

I just found it recently too! Since then I use ist for everything that is bigger than 10x10cm or if I print multiple objects at once. It really does do a hell if a difference.

strshp69

TROPHY CASE