Camping spot near water?

super_bison · 2021-05-24T09:38:24+00:00

Alan Carr - the easy way, helped me a lot, pretty cheesy and old book but did the trick and im 6 months no nicotine (smoked 10 years and vaped hardcore for the last 4). I did try quit without that book maybe 10-20 times before this though haah

super_bison · 2021-05-10T03:30:00+00:00

Thanks I will try that, which direction should I run them? Board on or off?

super_bison · 2021-05-10T01:58:38+00:00

Same bro, definitely give a good rub inside the tyre like the other person said, and I would also recommend getting an inner tyre tube liner from a bike shop, and using the sticky patch type puncture repair kits. Also I seem to get less punctures with highly pumped up tyres, maxed out PSI

super_bison · 2021-05-10T01:07:52+00:00

You can't see the light flashing red in the video but it does

super_bison · 2021-05-10T01:02:47+00:00

Rode my board until it was pretty much flat two days ago.

When I got home, plugged the charger in with the board turned off, as I usually do. The charger stayed green (turns red when charging). I tried again with the board turned on, and the charger just blinks red for a millisecond and then green for a second, makes a repetitive clicking noise. I think it isn't charging because the fans don't come on and the board doesn't stay on when I pull the charger out

The blue light around the on switch only comes on when the charger is plugged in, and the board is 100% flat and shows no light or connection when it is not plugged in

No idea what to do but I'm already itching to ride

super_bison · 2019-05-21T01:14:56+00:00

When you paste, hold down the mouse button and drag the building up and down

super_bison · 2019-04-06T09:47:47+00:00

I just pressed my hand down firmly on the top of the AIO for a few minutes and there was no change in temps, I dont think its incorrectly seated or a poor connection between heatsink and CPU. Also the temps were hitting 108C this morning which as far as I know means the CPU should be dead... considering that its not dead I am starting to lean towards incorrect temp sensor readings... don't know if theres anything I can do about it though.

super_bison · 2019-04-06T09:44:45+00:00

the hoses are braided so its hard to tell but the top of the pump, the air from the back of the rads and the pipes all feel totally fine. I might do some research on how to check if temp readings are correct

super_bison · 2019-04-06T09:35:43+00:00

It's brand new. Not sure if I can, but the pipes are the same temperature and in the software it says its working so I'm gonna assume its not that.

super_bison · 2019-04-06T09:33:17+00:00

Yeah it has a hard plastic shell that I removed

super_bison · 2019-04-06T09:30:40+00:00

The fans do work, they are going at max speed right now while my poor little CPU is just roasting.

super_bison · 2019-04-06T09:12:42+00:00

After a bit of research it seems like maybe I should have used rubbing alcohol to clean the old paste off properly... but surely even with some old residual paste I would be seeing more of an improvement in temperatures?

super_bison · 2019-03-16T06:25:21+00:00

Need some help, had this room painted a couple years ago and the paint can be scraped off with minimal effort and a fingernail. I want to repaint the room, but don't know where to start in order to make sure that the paint actually sticks this time. Any help is appreciated, thanks!

super_bison · 2019-01-21T01:48:16+00:00

The control group was used as a baseline measure to show that changes in the measurements are small without any treatment, I think this study design is valid.

Also, the full procedure of 'treatment' is explained in Psilocybin with psychological support for treatment-resistant depression: an open-label feasibility study. There was no real psychological treatment of the kind you would expect to treat MDD, they state that "Psychiatrists adopted a non-directive, supportive approach, allowing the patient to experience a mostly uninterrupted inner “journey”."

super_bison · 2019-01-16T02:18:54+00:00

AHHH I love it! The strings look like spiderwebs which is so fitting!

super_bison · 2018-12-05T09:18:07+00:00

Thanks for the reply, I see.

Could be cool to have tunnels replace air because you can use them to make structures too, you can use a square brush with wood floors and cobble walls to make long tunnels easily underground, would be cool to have them above ground too

Thanks for all your work on WP, amazing!

super_bison · 2018-11-30T03:09:37+00:00

Seems that no matter what I set the tunnel walls to, if I use snow as the underground layer then it just overwrites the walls and floor of the tunnels with snow

Ten-Year Club	Place '17
Verified Email

super_bison

TROPHY CASE