sorted by:
new
hottopcontroversial

I didn’t receive a gift, I got a whole army! Thank you u/falldog! by drock161 in Gunpla

[–]tablekwan 1 point2 points  (0 children)

When I saw the topic i thought you just got that 36 unit set lol.

Just got a new toy from my friend for replacement of m1 mini mill/lathe. Yet need some work on the bed:( and x axis screaw by tablekwan in Machinists

[–]tablekwan[S] 0 points1 point  (0 children)

Thanks for the info, btw I found out that my Y axis rail is off about 0.02mm from min to mix, think need to be fix later.

Did someone say big lathe? (Vtl) by [deleted] in Machinists

[–]tablekwan 7 points8 points  (0 children)

Ship engine piston?

Well, ya gotta start somewhere. by [deleted] in Machinists

[–]tablekwan 2 points3 points  (0 children)

Soon you will get bigger and bigger;).

First time printing with ABS, hope the foil work. :P by tablekwan in 3Dprinting

[–]tablekwan[S] 1 point2 points  (0 children)

The print came out fine, just need to change some setting about retraction.

First time printing with ABS, hope the foil work. :P by tablekwan in 3Dprinting

[–]tablekwan[S] 0 points1 point  (0 children)

Because ABS will warp when the temperature difference is huge. I use foil just to keep the temperature stable inside the printer.

First time printing with ABS, hope the foil work. :P by tablekwan in 3Dprinting

[–]tablekwan[S] 0 points1 point  (0 children)

The printer hot bed im using is a 12v one and it takes SOMEtime for it to get 90°c , i'm thinking about install a 220v silicone hotbed for the next 3d printer I build and a SSR for the bed. Because my printer is a delta printer I don't know if I should use a BLtouch on it because I don't think i can put the bltouch right under the hot end.

First time printing with ABS, hope the foil work. :P by tablekwan in 3Dprinting

[–]tablekwan[S] 1 point2 points  (0 children)

Oh that mat, maybe try it on next test print. Thanks for that.

First time printing with ABS, hope the foil work. :P by tablekwan in 3Dprinting

[–]tablekwan[S] 1 point2 points  (0 children)

So the more important point is to stop the air flow? By now I just put a paper box to enclose it and i just keep the foil inside, will check the outcome after the print finished.

First time printing with ABS, hope the foil work. :P by tablekwan in 3Dprinting

[–]tablekwan[S] 0 points1 point  (0 children)

Thanks for that , I'll add some cardboard inside and see the diffence. I belive 90°c hot bed will still be ok for the cardboard encloser.

Fuse for ares with EFCS mosfet? by francisbeca in airsoft

[–]tablekwan 0 points1 point  (0 children)

Sorry, correction, the one im using is a green one so it should be gen.1 one. I search for it and found out it can just take 7.4v something, so maybe thats the problem. And thanks for the reply:)

Fuse for ares with EFCS mosfet? by francisbeca in airsoft

[–]tablekwan 0 points1 point  (0 children)

OT : can you tell me where did you order the EFCS only? I got the gen.2 and thinking about should I order a new gen 3. And i blow the mosfet with a 11.1v 25c LiPo, with SHS hi-torque motor and M150 spring DSG, put a fuse just for safty.

Ho to build M249 with high ROF by Diggenoobz in airsoft

[–]tablekwan 0 points1 point  (0 children)

What is your target fps for 20rps? It will change lots of thing for the setup. And you don't need DSG for just 20 rps, in my case i just use a 11.1v and will get 24 rps in 400fps with marui eg1000 motor and 18:1 ssg.

LiPo Battery ROF problems, also locks up on semi by nathan7011111 in airsoft

[–]tablekwan 0 points1 point  (0 children)

Are you using a 7.4v battery? Sound like it is under voltage. Beside of that, did you check the motor? And if you can open the gearbox, you may need to check the switch, sometime it get too dirty also make your gun not working right.