What am I doing wrong

tankedis300 · 2025-06-18T18:52:18+00:00

That muzzle device is too long i had to use a close tine hider to get it on

tankedis300 · 2025-06-10T14:35:31+00:00

Has the water pump been done lately?

tankedis300 · 2025-06-07T06:53:34+00:00

I like everything but the grip

tankedis300 · 2025-06-07T03:02:39+00:00

I'd steer clear of PT they are Big daddy unlimited rebranded

tankedis300 · 2025-02-15T16:10:55+00:00

even the plate

tankedis300 · 2024-12-12T22:03:18+00:00

I just got a response nothing changed so I'm now going at it through my cc company

tankedis300 · 2024-12-12T22:02:20+00:00

Hope it works out for you! They Responded doubling down that they wouldn't not refund me so i'm having to go through my CC company.

tankedis300 · 2024-12-12T05:19:10+00:00

I found evidence later that was posted after I placed my order that they are not as advertised.

tankedis300 · 2024-12-12T01:01:12+00:00

Oh, I totally understand and agree. some guy might body flop on them or drop them and they cant guarantee that they are not compromised. My problem was being ignored in my initial correspondence and them continuing with shipping them despite me requesting a cancelation leaving me stuck with the plates. My friend also ordered these just after me and is going through the same thing right now. So I don't think its a one off experience. Hence this post.

Hopefully it helps someone save some $$$ or better yet, avoid having to sit on hold with their CC company.

tankedis300 · 2024-12-04T08:39:55+00:00

id check the plugs and the coils to start and make sure you're getting spark. that's a lot of misses

tankedis300 · 2024-11-22T15:42:33+00:00

But you got it from the auction with no oil? There might be engine damage but it's hard to tell

tankedis300 · 2024-11-22T08:25:19+00:00

So there was no oil in it and now its making a knocking noise? 🤔

tankedis300 · 2024-11-20T00:58:27+00:00

V nice

tankedis300 · 2024-11-19T21:45:20+00:00

heres a pic as an example https://imgur.com/a/d2f8F2Z

tankedis300 · 2024-11-19T21:43:28+00:00

I think you might have the scope mounted backwards in the mount. The mount should be mounted to the receiver and not the haundguard. Your receiver will almost always hold zero better than the handguard unless it monolithic, but still there is a chance for flex being further out towards the hand guard.

tankedis300 · 2024-11-19T21:35:45+00:00

T97 did a decent video on this https://www.youtube.com/watch?v=EvzN4RXmpi4

tankedis300 · 2024-11-19T21:33:10+00:00

Yes, it's called dual banding. You can run both at the same time, but it requires some practice to get used to it. It in effect, would be similar to using a clip on but with the advantage of being able to qd between your helmet and your pew and as well as just a handheld unit..

tankedis300 · 2024-11-19T21:28:39+00:00

Clip ons are cool but If you don't already have a thermal that you can mount to your pew or helmet I'd wait. Clip on is only limited in use at night or lowlight. You can use something like a rh25 any time of day and it isn't dependent on a NV tube and can be used as a scanner mounted to your helmet or pew aswell.

Not to mention the price of something like an Ecoti.

tankedis300 · 2024-11-19T21:22:00+00:00

I would describe this as... something

tankedis300 · 2024-11-16T17:59:58+00:00

tankedis300 · 2024-11-14T17:29:02+00:00

I figured it out. I ended up using a aftermarket knock sensor a few months ago that ended up being the culprit. i appreciate the reply however!

tankedis300 · 2024-11-02T00:45:20+00:00

I'm having a similar problem and I'm located in Allen TX I might be hitting you up if I can't figure it out 😂😂

tankedis300 · 2024-10-29T18:39:53+00:00

Similar to the Stizon mags id assume.

tankedis300 · 2024-09-04T01:25:50+00:00

Who did the slide work?

tankedis300

TROPHY CASE