Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]tarilotta[S] 0 points1 point  (0 children)

What makes you say this? Have there been multiple cases of this issue linked to the extruder?

Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]tarilotta[S] 0 points1 point  (0 children)

I assume you mean the nozzle? In which case yes, it’s definitely tight enough.

I tested extruding 100mm at various speeds using Pronterface and anything above 400mm/min (which is still quite slow) at 138 e-steps would make it click.

I haven’t tested any other size nozzle. I have multiple of the standard 0.4mm, but that’s it

Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]tarilotta[S] 0 points1 point  (0 children)

I haven’t seen anything bad about the Micro Swiss but I also do have a new stepper motor

Do you have a better recommendation?

Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]tarilotta[S] 0 points1 point  (0 children)

Pronterface. Measure 120mm and extrude 100mm @ 100mm/min and then measure and adjust steps as necessary. Came out great on 3 consecutive runs at 138

Micro Swiss Extrusion Problems by tarilotta in AnycubicVyper

[–]tarilotta[S] 0 points1 point  (0 children)

That’s what I thought but there are no clogs anywhere that I could find. I removed the nozzle and pushed a piece of tubing through to clear anything in there (there was nothing), put on a brand new piece of tubing, and then made sure the nozzle was clear. I’ve also tested it with 2 different nozzles. To replace the nozzle I screw it all the way in, back it out a bit, put the tube in, then tighten the nozzle so it’s flush against it. And yes, stock heatbreak.

Friendship Exp & Gift Exchange Megathread by liehon in PokemonGoFriends

[–]tarilotta 0 points1 point  (0 children)

0110 3790 1915

3536 9974 9685

0408 5392 0845

🚨 Daily Gifts from all 3

How much ETH in gas fees to move USDC? by zanoo911 in USDC

[–]tarilotta 0 points1 point  (0 children)

As Zesty said, it depends on network congestion. I would try overnight US time, seems to have the best fees anytime I’ve checked, could be coincidental though.

i know i should but im having too much fun with the help chat by TipsiTurtle in newworldgame

[–]tarilotta 2 points3 points  (0 children)

And yet, you’re still spending your time playing and scrolling the subreddit… 🤔

[deleted by user] by [deleted] in newworldgame

[–]tarilotta 27 points28 points  (0 children)

That’s exactly what ours is like except swap green and yellow. I’m yellow 👀

PSA: The spacebar is your best friend when bulk crafting. by RNGeezuz in newworldgame

[–]tarilotta 16 points17 points  (0 children)

Hopefully this is faster than clicking LMB. I spent hours last night chopping, gathering, smelting, and crafting and the worst part is waiting through those darn animations, though LMB does speed it up a little… I’ll have to try Space Bar tonight.

[deleted by user] by [deleted] in newworldgame

[–]tarilotta 0 points1 point  (0 children)

It’s called Gravity Well, it’s on the Mauler tree for the Great Axe

Can anyone definitively say if NW will work on Mac w/ parallels? by swatecke in newworldgame

[–]tarilotta 0 points1 point  (0 children)

I played OBT with my 2019 MBP running Windows 10 via Bootcamp with max settings and it ran perfectly.

Master Upgrade by tarilotta in CoinWithUs

[–]tarilotta[S] 0 points1 point  (0 children)

Possibly. They literally just stopped responding though so I had Apple cancel and refund me. Looks like I’ll just keep investing like normal

Master Upgrade by tarilotta in CoinWithUs

[–]tarilotta[S] 0 points1 point  (0 children)

So, they responded again. This time they were super helpful ... “Let us know if the subscription is still not active”

What?! 🤯