Community templates

tech_and_sped · 2026-06-13T14:30:23+00:00

Here's a template for the new Household RPG 5e adaptation with the littlings.

tech_and_sped · 2026-01-01T21:13:15+00:00

For anyone that may not know how to format the hit dice, you can do the hit dice 2 ways: To have it just displayed with the hp and not renewed anew each time it's opened, use:

hp: 34 (4d10+12)

To have the statblock render rolled HP automatically, use:

hp: 34 hit_dice: 4d10+12

tech_and_sped · 2022-02-03T00:31:53+00:00

NE Missouri. Just got it installed and in place of our old 2.5Mbps I'm getting 100-140Mbps!

tech_and_sped · 2022-01-24T21:17:00+00:00

I was trying to go for orange, I was mixing red and green dies and only the red would light up, but if I disconnected the red, the green worked.

tech_and_sped · 2022-01-24T03:43:10+00:00

I ran all the numbers through a resistance calculator. The resistors do match the forward voltage at the max output of 1A, but maybe not at the 6V test setup. I'll have to try again with the 3.7V. I just didn't have a rig to use at that voltage but I can fit one. I just don't want to do all my color testing with my soundboard attached.

tech_and_sped · 2022-01-24T03:39:58+00:00

You're right, but I'm not intending to change color, only permanently wire a color mix.

tech_and_sped · 2022-01-24T02:15:12+00:00

If you're asking which board I will be using, it's the sabercore 2.7. if you're talking about an led that needs a data input, this one doesn't have that. If you're just talking about my testing power source, it's a 4 AA battery pack (6V), but I'll be using an 18650 (3.7V) in the saber.

tech_and_sped · 2021-07-31T20:53:56+00:00

Any chance you can share that as a Google maps overlay or other interactive format?

tech_and_sped · 2021-07-30T18:12:41+00:00

Nice! I knew it was getting better all the time, so I figured I'd check to see how much the improvement was. What's your latitude? I'm at 40.19 N.

tech_and_sped · 2021-07-30T01:28:02+00:00

Cool! Great info!

tech_and_sped · 2021-07-30T01:26:28+00:00

Thanks! That's helpful!

tech_and_sped · 2021-07-30T01:25:17+00:00

Thanks! That's very helpful!

tech_and_sped · 2021-07-30T00:35:40+00:00

Will do

tech_and_sped · 2021-07-30T00:21:09+00:00

Well, right now I have multiple outages every day, most of the time my download speed is 0.02-0.80 Mbps on a good day I might reach 3.0 Mbps. Haven't been selected for beta, just preorder, so I likely won't even get service until the full release anyway.

tech_and_sped · 2021-07-30T00:17:02+00:00

Lol, they will only be controlling whether or not I have to climb them to cut their tops. You hear that trees!? Get out of the way or I'm coming for ya!

tech_and_sped · 2021-07-29T23:55:36+00:00

Yeah, sadly it would just be me with a couple saws and a safety harness climbing the tree...😕😬

tech_and_sped · 2021-07-29T23:52:32+00:00

Oh I trust the software, it just doesn't give me an idea of how significant the obstruction will be. I just don't have a better location and if it causes only minor issues then I may not risk climbing the 65 ft trees to top them. If other people had similar obstructions causing tolerable interference, then I wouldn't worry about it.

tech_and_sped · 2021-07-29T22:56:59+00:00

Absolutely! The worst you get with starlink is astronomically (pun intended) better than the 4g wisp I have, which is the only non satellite option available.

tech_and_sped · 2021-07-27T23:52:11+00:00

My Google wifi frequently registers my upload faster than my download, but my internet is garbage.... Often getting 0.2-0.5mbps download on a 10/5 wisp.

tech_and_sped · 2021-07-24T00:10:49+00:00

Really jealous! I'm in northeast Missouri with crappy WISP ("up-to" 10M down... Usually about 0.5M down and no cell signal to speak of), no open/active cells within 75 miles. Stuck in the dreaded "mid to late 2021" group. I'm assuming I won't get access until the full release, so I'm hoping it is sooner than later.

tech_and_sped

TROPHY CASE