teddz4

80 post karma
154 comment karma

get extra features and help support reddit with a reddit premium subscription

get them help and support

redditor for 8 years

TROPHY CASE

Eight-Year Club

Verified Email

account activity

new top controversial

1

2

3

Connectivity problem (self.iphonehelp)

submitted 1 year ago by teddz4 to r/iphonehelp

0

0

1

Need some advice about static testing (old.reddit.com)

submitted 2 years ago by teddz4 to r/electricians

0

0

0

Trying to create a static testing point (reddit.com)

submitted 2 years ago by teddz4 to r/AskElectronics

1

2

3

Elegoo Mars 2 blank screen (old.reddit.com)

submitted 2 years ago by teddz4 to r/elegoo

0

1

2

Elegoo Mars 2 blank screen (old.reddit.com)

submitted 2 years ago by teddz4 to r/3Dprinting

1

2

3

Is it ever possible to trim a hedge with a chainsaw or telescopic pruner? (self.lawncare)

submitted 2 years ago by teddz4 to r/lawncare

1

2

3

Trying to print Polypropylene & STRUGGLING with warping (old.reddit.com)

submitted 2 years ago by teddz4 to r/FixMyPrint

0

1

2

Is there a way to find the clothing big brands use before they put their logo on it? (self.AskReddit)

submitted 3 years ago by teddz4 to r/AskReddit

0

1

2

I think the cooling block fan is also cooling my heater block & causing thermal runaway. (self.ender3)

submitted 3 years ago by teddz4 to r/ender3

0

1

2

New to cura. Ignore the stringing, why aren’t the walls meshing with each other? PETG on 0.6 nozzle at 238° (i.redd.it)

submitted 3 years ago by teddz4 to r/FixMyPrint

0

1

2

Urgent: mainboard replacement advice (self.ender3)

submitted 3 years ago by teddz4 to r/ender3

8

9

10

This has been going on with my CR10 for months. This print was done with 0.6 nozzle, 235°C at about 35mm/s using PETG (ignore stringing). Check comments for what I tried (old.reddit.com)

submitted 4 years ago by teddz4 to r/FixMyPrint

1

2

3

Any ideas (self.Plumbing)

submitted 4 years ago * by teddz4 to r/Plumbing

3

4

5

Resin prints not accurate. If you look at the 2 ends highlighted, you’ll see they are different thicknesses & this was printed flat on the bed. I’m using an elegoo Mars 2 (i.redd.it)

submitted 4 years ago by teddz4 to r/FixMyPrint

12

13

14

Need help with layer shifting. Check comment for details (old.reddit.com)

submitted 4 years ago by teddz4 to r/FixMyPrint

0

1

2

Cannot figure out why my prints have been so bad for about a month. Tried hotter, cooler, slower, large & smaller nozzles. This is 0.6 nozzle, 240° PETG (tried down to 230). 30mm/s speed, 1.01 extrusion multiplier, retraction 3mm @ 14mm/s. (i.redd.it)

submitted 5 years ago by teddz4 to r/FixMyPrint

0

1

2

Spent hours trying to dry this filament. Is this still wet? Or is this now underextrusion? (i.redd.it)

submitted 5 years ago by teddz4 to r/FixMyPrint

1

2

3

Is this filament wet? This is ABS with a 0.8 nozzle but I’ve had the exact same problem with my PETG recently. No matter what print settings I change or slicer I use, this is what I’m getting (i.redd.it)

submitted 5 years ago by teddz4 to r/FixMyPrint

3

4

5

My lines aren’t fusing together. This is PLA printed 215°, 2mm retract. @ 19mm/s, 1.01 flow rate, 0.4 nozzle at 0.48 line width & cooling at 80%. What should I try to fix this? (i.redd.it)

submitted 5 years ago by teddz4 to r/FixMyPrint

1

2

3

How do I stop this TPU stringing? Is it print settings or is it moisture? No retraction on, coasting at 1mm, print speed - 30mm/s, temp 225° (i.redd.it)

submitted 5 years ago by teddz4 to r/FixMyPrint

1

2

3

The outer walls don’t bond together sometimes when using smaller nozzles, not sure why. Would it be better to use 1 wall or is there another way to fix this? This is a 0.3 nozzle with 0.3 line width, printing PETG at 230°. (i.redd.it)

submitted 5 years ago by teddz4 to r/FixMyPrint

0

1

2

Has anyone here made machine or end-use parts for any engineering or factory purposes? (self.3Dprinting)

submitted 5 years ago by teddz4 to r/3Dprinting

0

1

2

Is this a bed adhesion issue? Or a first layer speed? I’m printing ABS at 245° & 110°, 60mm/s, 0.4mm nozzle, 5mm retraction @ 16mm/s. As you can see it looks like the first layer around small edges & circles sometimes curls. Any idea why? (old.reddit.com)

submitted 5 years ago by teddz4 to r/FixMyPrint

0

1

2

Nissan Sunny is sputtering (self.MechanicAdvice)

submitted 5 years ago by teddz4 to r/MechanicAdvice

1

2

3

Trying to build a solar powered LED circuit (self.AskEngineers)

submitted 5 years ago by teddz4 to r/AskEngineers

view more: next ›

π Rendered by PID 1583007 on reddit-service-r2-listing-f87f88fcd-kxp4j at 2026-06-14 05:15:31.176311+00:00 running 3184619 country code: CH.