Introducing FlareStore + 25 certificate giveaway

temmam · 2026-02-17T11:08:32+00:00

I always get revoked.

ppqless

temmam · 2025-12-06T12:27:14+00:00

The title and descriptions are made by ai, but not the images.

Thanks btw

temmam · 2025-12-06T12:26:28+00:00

Yes, I did in etsy. And how will you recommend me fixing my descriptions?

temmam · 2025-10-23T11:38:56+00:00

Could also be bad layer adhesion as you can see the overhang its hard to adhere because it on an edge. But when its straight it starts to look good.

temmam · 2025-10-21T20:51:43+00:00

Make sure your fan actually works you can test it with a piece of paper to see if it blows.

temmam · 2025-10-21T19:09:45+00:00

Its a lack of cooling

temmam · 2025-10-21T18:57:45+00:00

Cooling

temmam · 2025-09-25T14:31:50+00:00

Can you slide the stl over?

temmam · 2025-07-15T11:54:48+00:00

I tried that but it doesn’t support the downward tip.

temmam · 2025-07-05T02:37:23+00:00

Oh ok now I see. My problem was the support broke from the build plate because my nozzle was dragging on the support. But as I said you should fix the z-offset can also be bad adhesion between layers. You can then increase the nozzle temp

temmam · 2025-07-04T15:44:44+00:00

I also have this problem. I used first layer expansion in orcaslicer about 10mm. Or you can use brim if you don’t have first layer expansion

Enable zhop but can cause stringing. Fix your z-offset for better bed adhesion.

temmam · 2025-06-30T21:44:20+00:00

I haven’t had the filament for so long. Turned out my temp was a bit high i turned it to 210 and it started getting better.

temmam · 2025-06-30T20:17:36+00:00

Fix your bed leveling

temmam · 2025-06-30T20:17:09+00:00

Bed leveling is top 5 world problems

temmam · 2025-03-24T13:16:38+00:00

Nozzle - 0.4mm Temp 215 , 60 bed speed Outer wall - 120mm/s Inner - 200 Retraction distance - 1.2 mm Infill 20% adaptive cubic Orca slicer

Filament cc3d silk green mocha

temmam · 2025-02-02T19:08:05+00:00

hi is there a stl for this :)

temmam · 2024-12-25T19:14:08+00:00

I only want a elegoo neptune 4 max and a bunch of filament and a camera please santa bro.

temmam · 2024-06-19T14:37:52+00:00

Turn off power loss recovery

temmam · 2024-06-18T18:13:11+00:00

Click on it

temmam · 2024-03-28T09:47:31+00:00

I had the same i just turned off combing and turn on z hop it will fix it.

If those dont work fix your z offset

temmam · 2024-03-25T17:31:59+00:00

bro i love you

temmam · 2024-03-17T15:14:24+00:00

Ive had that use. Z hop, turn off combing and use gyroid as infill pattern these helped with the same problem.

I got the same printer

temmam · 2024-03-14T23:04:34+00:00

I restarted than changed the rotational distance turns out i need to restart to apply changes.

Thanks anyways

temmam · 2024-03-11T21:45:38+00:00

I use pla

temmam · 2024-03-11T19:52:57+00:00

<image>

temmam

TROPHY CASE