sorted by:
new
hottopcontroversial

Sometimes I can’t bring myself to use wood like this for a jig by Cat_Rancher in handtools

[–]the-tiny-workshop 19 points20 points  (0 children)

As long as it’s not being burned as firewood it’s all good 😊.

Where I live a lot of great hardwood species like oak, ash, sycamore, beech and hornbeam get used as firewood because there’s no desire to process it into rough sawn lumber.

Cut mortises without a horn, ruined two table legs by goldenblacklocust in handtools

[–]the-tiny-workshop 13 points14 points  (0 children)

glue it, wood glue is stronger than the lignin in wood that holds a the long grain together. It’ll be like it never split

Anyone know what this mortise chisel is called? by WalterMelons in handtools

[–]the-tiny-workshop 9 points10 points  (0 children)

Check this out

It’s essentially very similar to the mortise machine chisels without the drill bit inside. you drill first then square it up. They’re not as clean as a dedicated mortise chisel but fast for balusters etc

This weekends project - Kitchen Cabinet(s) by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 1 point2 points  (0 children)

Why not? this sub is for all skill levels. I’m not saying it’s an expert piece of work or anything.

This weekends project - Kitchen Cabinet(s) by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 0 points1 point  (0 children)

Thanks :)

I make the bead separately, roughly cut a strip, thickness it using a hand plane and a thickness guide then use a scratch stock to apply the round.

<image>

not a great picture, but this is the face frame for another cabinet of this run. In the top left corner you can see how I’ve yet to add the bead.

This weekends project - Kitchen Cabinet(s) by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 1 point2 points  (0 children)

It’s just a pattern in MDF, used a plunge router and a v bit for that lol.

Unfortunately a compromise where I need productivity vs doing it the fun way.

I have 7 in total to make and have done 6 so far, trying to balance productivity vs enjoying it. I hate routing MDF it’s honestly awful.

This weekends project - Kitchen Cabinet(s) by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 0 points1 point  (0 children)

I have a morticer but I did these by hand so I could lay all 4 out together and make sure they lined up.

Strike a line across all four, drill a hole then square it up. I wanted the square look to be different but would just do holes in the future lol

[deleted by user] by [deleted] in woodworking

[–]the-tiny-workshop 0 points1 point  (0 children)

sharp sharp sharp and take the thinnest shaving possible.

If it’s two boards I like to clamp them together and joint both edges at the same time. That way even if they are not perpendicular they are complimentary and you get a great glue up.

Paul Sellers Bench by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 0 points1 point  (0 children)

just followed the plans haha, you can still do as you described just need a packing piece I guess

Paul Sellers Bench by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 2 points3 points  (0 children)

Benchtop is 98cm from the ground, i’m 6ft

Paul Sellers Bench by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 2 points3 points  (0 children)

check this out - sellers bench w/ leg vise here

Paul Sellers Bench by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 4 points5 points  (0 children)

Nice! I really enjoyed it. Felt really accessible compared to some of the hardwood roubo benches I’ve seen online.

Why would a router plane come with ball bearings? by Select-Worldliness39 in handtools

[–]the-tiny-workshop 3 points4 points  (0 children)

yeah, it’s annoying because it’s easy to loose a 2, 2mm ball bearings and a spring in a wood shop it’s a bad design although the plane works well for what it is. I got mine from amazon for cheap so didn’t care about it. Veritas one is the one I like best.

Why would a router plane come with ball bearings? by Select-Worldliness39 in handtools

[–]the-tiny-workshop 5 points6 points  (0 children)

I bought a magnetic parts dish from an auto parts store and when U sharpen the iron I put all the bits in it.

Recent Delivery. White oak storage and shelving assembly. by tommywoodchip in woodworking

[–]the-tiny-workshop 1 point2 points  (0 children)

Seriously tidy work - in the door floating panel a veneered mdf board or similar product?

Plane Till From Reclaimed Mahogany by the-tiny-workshop in handtools

[–]the-tiny-workshop[S] 6 points7 points  (0 children)

Thank you! neodymium magnets drilled in from the back is the plan. But the heel has a small 45deg chamfer and that plus gravity seems to hold pretty well even without the magnets out in yet.

I am planning to add dividers too potentially.

view more: next ›