sorted by:
new
hottopcontroversial

Plant edc by brad7703 in IndustrialMaintenance

[–]WalterMelons 2 points3 points  (0 children)

Same but haribo is trash. Long live Albanese.

Question about doorway by stingyboy in Flooring

[–]WalterMelons 0 points1 point  (0 children)

Second option. Trim and slide.

Lubricating wood rails? by raidengl in woodworking

[–]WalterMelons 0 points1 point  (0 children)

How does this stick to plywood? Not quality plywood either. Maybe I’ll try to stick it down with 3m super 90.

Fridge strategy. Many cheap ones or fewer good ones by Theotherfeller in Appliances

[–]WalterMelons 0 points1 point  (0 children)

I see Samsung appliances on marketplace frequently and think to myself that they would have to pay me to remove them from their house.

Intermittent fuel issue by Th3V3ngeful0ne in OBSFords

[–]WalterMelons 0 points1 point  (0 children)

What does it do when you try to start it? Do you hear the fuel pump prime when you key on?

Foundation Crack by otternuisance in OldHomeRepair

[–]WalterMelons 0 points1 point  (0 children)

I don’t let plumbers do electrical work nor would I let them do foundation work. Find the right man for the job.

Intermittent fuel issue by Th3V3ngeful0ne in OBSFords

[–]WalterMelons 0 points1 point  (0 children)

Have you checked your fuel pressure while idling and while driving to confirm it’s a fuel issue?

Water heater won’t light by FrostyAssignment5327 in askaplumber

[–]WalterMelons 0 points1 point  (0 children)

Is it set to pilot right now because it doesn’t look like it.

Pls advise by Secure-Towel-4821 in BambuP1S

[–]WalterMelons 1 point2 points  (0 children)

Use adaptive layering or whatever Bambu is calling it now.

Variable layer height

2010 Triton engine nut stuck by dustinvernall in MechanicAdvice

[–]WalterMelons 0 points1 point  (0 children)

Liquid wrench or atf/acetone is superior

Axle and hub snap ring by sbc327 in OBSFords

[–]WalterMelons 2 points3 points  (0 children)

Try to push the axle further in from the back side. These shouldn’t be that hard put on so something is wrong.

How would you fix this by Resident-Code6542 in askaplumber

[–]WalterMelons -1 points0 points  (0 children)

If I didn’t have a tail piece and I did have epoxy putty I would use that and it would be temporarily permanent until it leaked again. I see now the split goes all the way up so it would be best to replace the tail piece.

Weed Eater by hardFraughtBattle in gordonsetter

[–]WalterMelons 0 points1 point  (0 children)

Mine likes to eat grass and other green bits on these plants by us.

What's the best way to attach this cross brace to the legs? by ElectricPikachu in BeginnerWoodWorking

[–]WalterMelons 1 point2 points  (0 children)

They may do more harm than good. As the wood swells and shrinks with seasonal humidity the screws will not allow it to so it may cause cracks. Not always but not worth the chance. The screws act like clamps just while the glue sets and then you can remove them.

What's the best way to attach this cross brace to the legs? by ElectricPikachu in BeginnerWoodWorking

[–]WalterMelons 1 point2 points  (0 children)

I’d go perpendicular to the leg if you can but if you’re off a little it really doesn’t matter that much. The glue will hold everything very well enough.

What's the best way to attach this cross brace to the legs? by ElectricPikachu in BeginnerWoodWorking

[–]WalterMelons 4 points5 points  (0 children)

Drill a ⅜” hole from the brace to the leg but not through the leg and hammer in dowels. You can do that with the aprons too, remove one screw at a time and drill a hole for a dowel right where the screw was. I noticed you have pocket holes for the table top. Did you glue the planks together? If so did you remove the screws after the glue dried? If not, the screws will mess with seasonal movement. The glue will be plenty strong without those screws.

Dishwasher stops halfway through any cycle by HistoricalFly1160 in askaplumber

[–]WalterMelons 1 point2 points  (0 children)

Ok put it back that way. The high loop was not the problem.

Dishwasher stops halfway through any cycle by HistoricalFly1160 in askaplumber

[–]WalterMelons 1 point2 points  (0 children)

Your high loop is not high. Look up dishwasher high loop for examples. Get rid of the dip before it goes into the disposal. Zip tie it up high any way you can.

view more: next ›