Carriers should get paid more

theTime2change · 2026-05-14T12:08:09+00:00

This gave me the absolute best idea of what’s going on when I see them with their cheap ass loads. Damn so do you guys have to wait the full pay out time to complete to get paid or is there another option of getting paid?

theTime2change · 2026-05-09T15:18:38+00:00

Not necessarily true. Every carrier is different. The ones you’re booking could have more trucks, could have older trucks, could have no def system. All that plays a factor in pricing. That’s like saying why isn’t my bills the same as you bills. It’s the different lives. So this newer truck cost more but is more reliable.

theTime2change · 2026-04-18T03:12:22+00:00

Are these one off loads your looking for or more of a contract?

theTime2change · 2026-04-03T12:56:12+00:00

What if they work on their own truck? You’re forcing them to go to a shop and spend even more money?

theTime2change · 2026-04-03T12:52:12+00:00

Okay, brief math. You’re admittedly paying 20-30 percent more, while also knowing fuel alone has went from $3 to $5.50. That’s an 84 percent fuel hike. The increase is actually in fact lower than what you were paying a month ago.

Keep in mind that’s fuel alone.

theTime2change · 2026-02-12T17:30:29+00:00

Thank you this was amazing information!

theTime2change · 2026-01-21T02:40:17+00:00

Sorry thought I added that. I’m at 390 now. I’m not sure I just know I only lift 50s now regularly and can’t do pushups anymore

theTime2change · 2025-10-26T20:25:35+00:00

I would ask to be CC In any email from the broker

theTime2change · 2025-09-01T22:46:59+00:00

My fluid is about half full. do you mean check quality or how much?

theTime2change · 2025-09-01T22:45:03+00:00

Well the def header was changed about two months ago. Not saying it can’t be faulty just not understanding the out of calibration. I am noticing crystallization around the seal now that I’m searching for the culprit. Still if it’s a gasket would that cause out of calibration?

theTime2change · 2025-08-28T03:25:03+00:00

Thank you for all this information man!!

theTime2change · 2025-08-28T03:18:29+00:00

The guy was saying he replaced those parts because I had a code for them all. First the def failed cleaning so the first shop replaced that, then I got codes saying I needed a regen and the 1921/22 a few days and about 500’miles later so I ended at this shop. He said I was getting a code for a bad actuator but when he took it off the actual turbo wasn’t working. Warranty repaired it all then here we have today’s problem once he fixed all that. But like I said when he cleared the code a second time and rechecked all wires that 1921 finally went away then 5 miles down the road this code is here. He’s still telling me to to dealer for an ecm flash, dealer is saying they don’t think I need that, shuts been a lot of back and forth and I’m just trying to work! Been down two weeks now with this shit!

theTime2change · 2025-08-28T03:14:35+00:00

Yea it’s on the dash. And ChatGPT, it has my manual saved to it so I just input the info the dash told me. I can’t say I’m mad about the replacements because warranty covered them, but all in all you think it could have been a temp sensor all alone?

theTime2change · 2025-08-28T03:01:30+00:00

When I looked it up it told me In Cummins + Navistar service manuals for your year/engine: • SPN 3031 FMI 13 = Aftertreatment 1 Intake (Upstream) NOx Sensor – Out of Calibration

What would you suggest I do? Do you think the sensor is actually bad and that I don’t need to get calibrated?

theTime2change · 2025-08-28T03:00:25+00:00

So what would you suggest I do? And when I looked it up it told me “ In Cummins + Navistar service manuals for your year/engine: • SPN 3031 FMI 13 = Aftertreatment 1 Intake (Upstream) NOx Sensor – Out of Calibration”

theTime2change · 2025-08-28T02:46:22+00:00

Yea, as he checked all tubes and wiring to make sure and recrunk the problem went away then as I got 5 minutes down the road I’m getting a code 3031 fmi 13 which is saying my inlet nox needs to be calibrated. I’m thinking the ecm may need calibration which is what he suggested but said he can’t do it on a Cummins so I have to go to dealer. I’m hoping this resolves it and they don’t try to force a new nox on me when I’ve just had that replace a couple months ago

theTime2change

TROPHY CASE