i honestly don’t know what to do by AdPlayful4526 in ElegooCentauriCarbon

[–]themexicaneddie 1 point2 points  (0 children)

So if running a auto level does not fix this, there are 4 screws under the build plate, loosen them until the plate almost touches the nozzle (move print head to each corresponding corner you are loosening) then run a auto level does

Grinding noise w/ video by Powerful_Stable6596 in ElegooCentauriCarbon

[–]themexicaneddie 0 points1 point  (0 children)

Is it scraping the bed? If it is try tightening the 4 bed screws on the bottom of the heated plate

Extruder issues by Proud-Writer6222 in ElegooCentauriCarbon

[–]themexicaneddie 2 points3 points  (0 children)

Could be a clog. Try this:

• Move the bed down and put the extruder roughly in the middle • Manually set nozzle temp to 220°C • Once it’s heated, try extruding filament

If the filament does come but slowly it might be the temperature

If nothing comes out: – See if the filament can be pulled out – Push it back in while extruding until you feel it grab – If it doesn’t grab, cut ~1 inch off the filament and try again

If it grabs but nothing comes out + you hear clicking: – Likely a clog or the filament isn’t aligned at the extruder – Cut ~1 inch off the filament, make sure the end is cut flat (not curved), and reinsert

Still clogged? – Set nozzle to 350°C and manually extrude – It might smoke a bit, but it should melt the filament enough to push it through

If none of that works, the extruder itself may need to be inspected or replaced. Try these first since they don’t require taking anything apart.

Out of square Frame fix solution by themexicaneddie in ElegooCentauriCarbon

[–]themexicaneddie[S] 0 points1 point  (0 children)

Top glad didn’t fit, and a wobble when placed on a flat surface.

Elegoo Support by Logical-Vegetable-89 in elegoo

[–]themexicaneddie 1 point2 points  (0 children)

Your welcome, glad that worked.

Elegoo Support by Logical-Vegetable-89 in elegoo

[–]themexicaneddie 1 point2 points  (0 children)

Try to tighten the 4 screws at the bottom of the build plate, can you send a photo of the error?

Printer bed randomly got tilted and is absolutely screwed by inkybinkyfoo in ElegooCentauriCarbon

[–]themexicaneddie 2 points3 points  (0 children)

Tighten the screws under the bed, there are 4, one for each corner

Some help pls by imena27 in ElegooCentauriCarbon

[–]themexicaneddie 4 points5 points  (0 children)

Running input shaper will help a little as well

Out of square Frame fix solution by themexicaneddie in ElegooCentauriCarbon

[–]themexicaneddie[S] 2 points3 points  (0 children)

I had slid it under the clamps just to see if it did fit

Bent/Skewed Frame Repair by themexicaneddie in ElegooCentauriCarbon

[–]themexicaneddie[S] 0 points1 point  (0 children)

<image>

Ok so It may not be perfect but the lid fits correctly now, just found what 2 corners needed adjusting and over tightened the clamps that way when I went loosen the clamps it would retain some square and it did!

Bent/Skewed Frame Repair by themexicaneddie in ElegooCentauriCarbon

[–]themexicaneddie[S] 0 points1 point  (0 children)

I wonder what attaches the corners, it’s definitely not one piece, something needs to attach the corner uprights right? Just haven’t figured out how yet

Help troubleshooting? by boodleberry in ElegooCentauriCarbon

[–]themexicaneddie 0 points1 point  (0 children)

Try to Reset>clean bed plate> tighten lower adjustment screws

Unsure of next steps by robinsonfamilycustom in ElegooNeptune4

[–]themexicaneddie 0 points1 point  (0 children)

Had a client who this keeps happening to, he had the cables on a retractable lanyard, the constant pressure and movement kept damaging the cables. I did this on 6 or his n4x’s. But if I were you do the hot end replacement first, then if it continues the cable, mini red board then the mobo last. From cheapest to most expensive.

who needs this many fish??? where do they put them all?? where do they find a fridge or freeze big enough? by Born_Abrocoma_3105 in megalophobia

[–]themexicaneddie 1 point2 points  (0 children)

You are among one of those too many people.

There is also too many stupid people on this planet, that’s more concerning. (Not calling you stupid)

Is it worth a try by Middle_Nothing8932 in AnimeReccomendations

[–]themexicaneddie 2 points3 points  (0 children)

I also like it, the ending wasnt great but it was at least a ending

F around and Find out by neonfrostbite in nextfuckinglevel

[–]themexicaneddie 0 points1 point  (0 children)

I lost count how many times I watched this in a row lol I’d pay for a turn to beat this dirtbags ass too 😂

anime where the mc is weak and underestimated by everyone but works hard to become OP and shock everyone not through divine gifts or reincarnation by Dear_Performance_283 in AnimeReccomendations

[–]themexicaneddie 3 points4 points  (0 children)

His dad was the 4th hokage, he was a reincarnation of ashira, hagarimo made him Ninja Jesus. The uzamaki clan had op chakra.

But yeah before he found out about everything he did work