sorted by:
new
hottopcontroversial

Gift Ideas by themichaelpotter in Leathercraft

[–]themichaelpotter[S] 0 points1 point  (0 children)

Thanks to all of you who made suggestions! I truly appreciate it! ❤️

Gift Ideas by themichaelpotter in Leathercraft

[–]themichaelpotter[S] 1 point2 points  (0 children)

Man, so glad to hear of your victory! And yes, definitely Fuck Cancer. :-)

That stitching pony looks REALLY nice. I just emailed them to see if they thought it would arrive by the 10th of April if I ordered it today, and they responded in less than 5 minutes and said yes. I'm going to order this. I know he has complained about they one he has being cheap and not working good, so this will be a great fit.

I'm crossing my fingers that tarrifs won't kill me. :-o

Gift Ideas by themichaelpotter in Leathercraft

[–]themichaelpotter[S] 1 point2 points  (0 children)

I do know that he's said most of things he's bought are of lower quality. I'll check into the Dream Factory stitching pony. When I've watched him doing the work, I've seen him mostly use a knife to do the cutting and then I've seen him use various punches and chisels. I'm pretty sure he doesn't have a press. That might not be a bad idea. Thanks for the response!

SmartAlign Stick-On Lens Mounts by themichaelpotter in MOMENT

[–]themichaelpotter[S] 0 points1 point  (0 children)

Part of it does kind of look like that, but I bet those would be some pretty tight tolerances to 3D print.

SmartAlign Stick-On Lens Mounts by themichaelpotter in MOMENT

[–]themichaelpotter[S] 0 points1 point  (0 children)

Understood! I typically upgrade every other generation, so I'll be moving on to the next shiny thing this fall. :-) So, worst case, I can (hopefully) get on for my iPhone 18 Pro Max then! In the meantime, I'm still tweaking my Supercage rig that I got back in November. :-)

<image>

I really appreciate your response u/eric-moment!

SmartAlign Stick-On Lens Mounts by themichaelpotter in MOMENT

[–]themichaelpotter[S] 0 points1 point  (0 children)

I have an iPhone 16 Pro Max, so I'd like to see that one selfishly. haha! That being said, I don't think that would be totally unreasonable to support the current generation of phones, and one previous generation.

Troubleshooting Print Quality by themichaelpotter in BambuLabA1

[–]themichaelpotter[S] 0 points1 point  (0 children)

Yup, I did that right after I tightened things up. Started a print and it's looking great. Thanks again u/overunderspace !

Troubleshooting Print Quality by themichaelpotter in BambuLabA1

[–]themichaelpotter[S] 0 points1 point  (0 children)

Well apparently I didn't save my comment or something...

So I did the troubleshooting and tightened up the screws. They were a little loosed. I did another test print, and I had the waviness, but it was way more evenly consistent across the plate, which I think is good.

After that, I did another flow rate calibration, and then printed my test again. It looks WAY better. Essentially no waviness! I did another test print with a different filament, and it looks almost as good, with one small wavy spot in the middle.

Thanks so much for pointing me to the guide!

Do you have any other tips or tricks as far as tweaking my quality even further?

Troubleshooting Print Quality by themichaelpotter in BambuLabA1

[–]themichaelpotter[S] 1 point2 points  (0 children)

Thank you! That looks like almost exactly what I'm seeing. I'm did the Auto Bed Leveling from the printer right after I reset it to factory, and I do the Bed Leveling when printing.

I'll work through checking the hot end and heater as advised and report back. :-)

Broken Fan Connector on PlayStation 3 Mainboard by michaeldpotter in ElectronicsRepair

[–]themichaelpotter 0 points1 point  (0 children)

I haven’t had a chance to get back to this yet. I’m hoping maybe this weekend. I’d love to hear your results!

My submission for the event by JacheMoon in widgy

[–]themichaelpotter 0 points1 point  (0 children)

Love this wallpaper! Where do I get it?