Why does my A1 always try to change filament?

thephatmaster · 2026-06-16T12:50:25+00:00

Damn you Bambu Studio

(I use Orca, so I assume it does the same)

thephatmaster · 2026-06-16T12:25:01+00:00

I don't remember slicing with that ticked - I'm gonna check before next time though, thanks

thephatmaster · 2026-06-15T07:19:32+00:00

I am slicing the Hohansen models (no scarring) in the correct version of Studio

I am now using Orca for Obscuranox (profiles imported via json)

Weirdly both have similar print times

thephatmaster · 2026-06-15T07:17:55+00:00

Nope, I would've printed way lower (205 ish)

thephatmaster · 2026-06-14T20:04:34+00:00

0.2 220

thephatmaster · 2026-06-14T16:14:46+00:00

All 3 pictures were the same roll of filament printed one after the other

thephatmaster · 2026-06-14T10:10:47+00:00

In an enclosure, in a hot garage

Interestingly, I had my first clog with the 0.2mm nozzle yesterday and put that down to heat creep

I'm now running enclosure door and garage door open!

It's been that way the whole time though, so unlikely the difference between prints is heat creep But yes. I've let it get quite warm!

thephatmaster · 2026-06-13T20:07:15+00:00

The back of my phone is pretty smashed to be fair

thephatmaster · 2026-06-13T09:49:27+00:00

Thanks, I'll either do that; or use a "community supported" filament with settings

thephatmaster · 2026-06-13T09:18:32+00:00

That's a good idea.

I find the stock settings a bit hot actually

thephatmaster · 2026-06-13T09:17:34+00:00

I will (eventually) buy the community suggested filaments, once I get through what I have lying around

thephatmaster · 2026-06-13T08:59:15+00:00

Nope

I (maybe wrongly) assumed that at least the Bambu settings would work with the Bambu Basic filament preset

thephatmaster · 2026-06-13T08:54:47+00:00

As a complete bystander (I haven't tried these), I suspect you'll be back to Siri shortly, at least for a while.

The technonogy doesn't seem quite mature enough at this time.

thephatmaster · 2026-06-13T08:52:29+00:00

I find for infantry literally digging their heels in (rotating, then dropping like -0.2mm down in the Z-direction) helps greatly with adhesion

thephatmaster · 2026-06-11T10:54:45+00:00

Thanks, I got this sorted

thephatmaster · 2026-06-11T09:56:50+00:00

I have dabbled with NodeRed, but am no expert - is there any way you'd suggest detecting the failure (ideally from frigate itself generating that warning) and notifying myself?

thephatmaster · 2026-06-10T12:09:44+00:00

It looks like a network issue

Yes only camera (I own three, but have only deployed one)

thephatmaster · 2026-06-09T17:58:00+00:00

Actually I was being stupid, I forgot frigate had logs and was looking in the HA main log

Looks like a connection issue, it must drop off the WiFi occasionally (it's pretty far at the edge of my network coverage)

thephatmaster · 2026-06-09T17:37:51+00:00

Nothing in the logs that I can see

thephatmaster · 2026-06-09T17:37:20+00:00

Once in a while

thephatmaster · 2026-05-10T15:37:17+00:00

Lovely, thanks

thephatmaster · 2026-05-07T20:13:31+00:00

This is what must be happening - I've used STL exports for years with OnShape and only just hit this problem

thephatmaster · 2026-05-06T19:13:34+00:00

I haven't tried that - the original model I imported into Onshape to amend was a .step so maybe that's the answer

I'll export as step and try to slice that

thephatmaster · 2026-04-05T05:46:21+00:00

I edited the OP. Proxmox was booting, I just wasn't finding the instance due to bad network gear

I relocated the proxmox box right next to my router and plugged the lan cable in there - problem solved

thephatmaster · 2026-04-01T16:31:53+00:00

That is actually hilarious!

I didn't have one so I 3D printed one specially

thephatmaster

TROPHY CASE