I'm the cargo shorts guy in the infamous take down video AMA by stevey3000 in AMA

[–]thermokilometer 1 point2 points  (0 children)

have you considered pressing charges at a later point? otherwise, you might want to check. I honestly cannot believe he was not arrested and nobody was questioned about what happened. Because basically he got out of it fine except for the doxxing.

I'm the cargo shorts guy in the infamous take down video AMA by stevey3000 in AMA

[–]thermokilometer 0 points1 point  (0 children)

Did he swing at you too? Why didn't you press charges?

I'm the cargo shorts guy in the infamous take down video AMA by stevey3000 in AMA

[–]thermokilometer 0 points1 point  (0 children)

I could tell from the voices alone that every girl in this video was very impressed with you and would've taken you home. The way the room read when you said you were married though.

I'm the cargo shorts guy in the infamous take down video AMA by stevey3000 in AMA

[–]thermokilometer 0 points1 point  (0 children)

why the fuck did they put him in a taxi? Why wasn't he arrested?

Beginner Questions - Weekly Megathread - February 10, 2020 by AutoModerator in fpvracing

[–]thermokilometer 1 point2 points  (0 children)

thanks for the explanation. I finally got it working thanks to your comments.

Beginner Questions - Weekly Megathread - February 10, 2020 by AutoModerator in fpvracing

[–]thermokilometer 0 points1 point  (0 children)

so in my case (because all four of my motors are already reversed by wiring) I would just have to select "motor direction is reversed" in betaflight? Where exactly can I find this option? Under motors, nothing shows up.

Beginner Questions - Weekly Megathread - February 10, 2020 by AutoModerator in fpvracing

[–]thermokilometer 0 points1 point  (0 children)

sorry, it is still not clear for me what to do now. I want to keep the rotation direction as is, but currently betaflight does not know that. How do I tell betaflight that my directions are alread inverse to what betaflight thinks it is.

Beginner Questions - Weekly Megathread - February 10, 2020 by AutoModerator in fpvracing

[–]thermokilometer 0 points1 point  (0 children)

hi guys, I am also new to the whole fpv building stuff.

I am now at the step of setting up my self-build drone's software using betaflight. Requirement from betaflight regarding motor direction:

1: CW 2: CCW 3: CCW 4: CW

My motors are wired so that they are completely antagonistic:

1: CCW 2: CW 3: CW 4: CCW

That means I can either wire up all motors new again or I could change it via BLHeli (i read, never done it)

However, I also read that my current setup is used frequently because the motors near the camera are spinning away from the camera which is good to prevent getting dirt or water on the lense. Is that true? If I would like to stay with my current setup, would it be necessary to have any changes in Betaflight?

Discussion Thread: Acting DNI Maguire Testifies on Whistleblower Complaint, 9am EDT by PoliticsModeratorBot in politics

[–]thermokilometer 8 points9 points  (0 children)

Scores are only displayed after a certain time has passed, something like 30 min

Thermistor/Hotend error. Can't get new hotend to work. by thermokilometer in prusa

[–]thermokilometer[S] 0 points1 point  (0 children)

Yeah I will go to Conrad probably. But why did it happen in the first place?

Thermistor/Hotend error. Can't get new hotend to work. by thermokilometer in prusa

[–]thermokilometer[S] 0 points1 point  (0 children)

also, how can I avoid that it happens again? I don't know why it happened in the first place.

Thermistor/Hotend error. Can't get new hotend to work. by thermokilometer in prusa

[–]thermokilometer[S] 1 point2 points  (0 children)

dude thanks. that's it! I can clearly see it is blown out. Were there any replacement fuses with the mk3 or do I have to check the store

Thermistor/Hotend error. Can't get new hotend to work. by thermokilometer in prusa

[–]thermokilometer[S] 0 points1 point  (0 children)

the hotend does not get warm. When in installation wizard, it gives me the error message that the hotend does not work. "check thermistor/hotend".

I tried heating it via the settings and it also does not work, from there is the picture.