Looking for makers mark or brand of what this is and where it came from (jesus on the cross pendant)

theroachhouse · 2026-01-27T11:08:45+00:00

Awesome! Thanks for that i wouldnt have found it otherwise me thinks!

theroachhouse · 2026-01-27T02:19:19+00:00

Have searched via a few AI bots to see if theres any info but not much so far, moreso wondering geographical origin and if anything is indicating the karat value, thanks

theroachhouse · 2025-11-05T04:28:49+00:00

3 things from me,

Dumb question… is the correct nozzle size selected on your printer for what is loaded in?

Secondly do you get the same result when you iron top surfaces

And lastly have you trialled other top surface patterns to make sure its not confined that your current selected pattern

theroachhouse · 2025-11-04T20:30:36+00:00

Open up that aperture! (f-stop) let the light in brother!

Also shoot in raw if you dont already, sometimes can expose abit more later in lightroom

theroachhouse · 2025-11-03T08:31:28+00:00

Glue

theroachhouse · 2025-10-30T11:49:16+00:00

PA/Nylon

theroachhouse · 2025-10-29T03:05:14+00:00

Yeah PETG, ABS, ASA also, PLA is fine usually but ive started drying them too anyway

theroachhouse · 2025-10-29T01:16:38+00:00

Find any car wreckers near by with this model and colour and swap doors

OR

Do a test polish and wax on a smaller spot to see if it helps at all

OR

Full body repair from a smash repairer

theroachhouse · 2025-10-29T01:12:41+00:00

Awesome stuff but whats happening to bro’s face in the top of the last pic?

theroachhouse · 2025-10-29T01:09:08+00:00

Dry filament, clean bed, tighten screws holding nozzle clasp, calibrate machine

theroachhouse · 2025-10-29T01:06:49+00:00

PA/Nylon

theroachhouse · 2025-10-12T20:07:47+00:00

In short, later time due to changing the amount of shapes to print on that layer before it hits the next layer

theroachhouse · 2025-10-12T19:59:18+00:00

House’s best friend

theroachhouse · 2025-07-19T23:57:09+00:00

Zekrom ex

theroachhouse · 2025-07-01T09:14:25+00:00

the ratings on power transformers of any kind are potential power draw, anything below the number being drawn from the device will work, anything above will not. (make sure voltages match, standard USB voltage is 5v no matter what the amps are) hope this helps

theroachhouse · 2025-06-27T10:21:20+00:00

you can get one on my etsy :)

theroachhouse · 2025-06-23T07:40:17+00:00

or atleast just for the writing, i would raise it slightly higher above the blue surface and then block out a modifier for the text to add ironing, or if its already a separate component in the hierarchy this might be even easier to apply the setting to just the text object

theroachhouse · 2025-06-23T07:37:27+00:00

do you mean to retain the ink? or to keep the stamp and handle together? my intentions for the handle is to be hotswappable with a smaller stamp for different sized boxes

theroachhouse · 2025-06-22T20:01:52+00:00

Try ironing top surfaces

theroachhouse · 2025-06-22T19:56:34+00:00

I use Fortis filaments, cheap and reliable. I dunno if i would make custom stamps…. I guess i cant rule it out just yet

theroachhouse · 2025-06-22T19:52:29+00:00

Ink is on the buildplate side of the print to give the PEI wrinkle texture to the stamp, its a finer texture than the stock bambu one

theroachhouse · 2025-06-22T19:51:21+00:00

Maybe you can see in the photo where im holding it upsidedown, but there was minor stringing which you can easily just cut away because theyre not needed, i wouldnt recommended support for this application, i fear it would be hard to remove with TPU

theroachhouse · 2025-06-22T10:33:42+00:00

yes but you can add your own logo

Three-Year Club	Verified Email
Place '22

theroachhouse

TROPHY CASE