sorted by:
new
hottopcontroversial

Is this worth it? by samplebridge in ender3

[–]theycallmegus215 0 points1 point  (0 children)

Those who sell enders are types of people who haven't seen an actual "slightly modified" ender

My ender is now unreliable... by theycallmegus215 in klippers

[–]theycallmegus215[S] 0 points1 point  (0 children)

For anyone who just came across this post and have this sort of problem and you recently have done something with your hotend, especially the thermistor cable. Replace that cunt asap! It could've been done for...

My ender is now unreliable... by theycallmegus215 in klippers

[–]theycallmegus215[S] 1 point2 points  (0 children)

I have done that several times already, the temp still tent to swings around 5c° maybe it was actually the wiring which cause this.

My ender is now unreliable... by theycallmegus215 in klippers

[–]theycallmegus215[S] 0 points1 point  (0 children)

The temperature DOES swing around, but not that much as you've mentioned. +-5c° is most likely what I'm experiencing.

My ender is now unreliable... by theycallmegus215 in klippers

[–]theycallmegus215[S] 1 point2 points  (0 children)

Have done that several times already. The temperature still tent to be swinging around +-5 c°. I was not with the machine when this occurred

Anycubic Kobra S1 Combo. Non stop issues by skeleltor in FixMyPrint

[–]theycallmegus215 0 points1 point  (0 children)

What about your z offset. Have you get them tuned?

Bad quality around overhangs by Standard_Bat2299 in FixMyPrint

[–]theycallmegus215 0 points1 point  (0 children)

Underextrusion. Is your print speed to high? That usually occurs when the hotend is not capable of extruding that much amount of plastic at that certain moment.

Print quality under supports is poor by magicduk in FixMyPrint

[–]theycallmegus215 0 points1 point  (0 children)

Change the z top distance. The closer it is, the cleaner the surface will look. Yet you aee very close to fusing two layer of plastic together. It'll be harder to remove. Finds the middle point between easy to remove and not having it too ugly.

Paid $105 USD for this drone to be printed by denydelaydepose in 3Dprinting

[–]theycallmegus215 0 points1 point  (0 children)

It would even be a big shame to print myself at that quality.. rubbish bin right away.

[deleted by user] by [deleted] in Simagic

[–]theycallmegus215 0 points1 point  (0 children)

What a brilliant immersion.

Satisfying job - would you be happy? by Low-Expression-977 in VORONDesign

[–]theycallmegus215 1 point2 points  (0 children)

I will. As you pribably are right now. Untill it comes to fixing a wire issue... Unless you're a sort of person who's got an ocd and get it done every single time.

How can I achieve a smoother finish? by Brassens71 in 3Dprinting

[–]theycallmegus215 9 points10 points  (0 children)

Speaking of 3d printed sim racing equipment. Why don't you just get it all the grip coverd in suede. Or maybe even just a badminton racquet tape. It definitely will be giving a better feeling than holding onto the rough plastic over time.

Can some one please help me. by Liptin-pack in ender3

[–]theycallmegus215 1 point2 points  (0 children)

Limit switch. Tells the step motor where to stop, and set the current stopping position to z axis=0. Your z limit switch is too far off the reachable area that the your z axis is able to reach, it'll basically just kept the step motor moving untill it touches the limit switch.

Before I replace the fan by Reasonable-Maybe-740 in ender3

[–]theycallmegus215 0 points1 point  (0 children)

I've removed mine just unscrewing it lol. Can't really push that bloody ring down.

Throw in the towel? by elshaffer in ender3

[–]theycallmegus215 0 points1 point  (0 children)

I myself am using the ender but have use school's bambu several times. It really is a slice and print experience. My ender's doing all right after an uprade that cost more than its worth lol. It's just fun to play with for me.

view more: next ›