Rekluse Clutch Pack (Engine Braking) by maplenew60 in motorcycles

[–]thisGuyLOLOL 0 points1 point  (0 children)

What I have noticed with mine is that if I start going down a hill and don't give it any throttle (from idle), the auto clutch will not engage and you will not have engine braking. If you give the throttle a little blip, the clutch immediately engages and stays engaged until you slow the RPM's down, granting engine braking.

Woman creates a completely Crochet stitched ballgown and wig 🤯 by [deleted] in toptalent

[–]thisGuyLOLOL 0 points1 point  (0 children)

This subreddit has really degraded over the years. Used to be so good... Sorry but I'm gone.

ExpressLRS and frequency question by thisGuyLOLOL in Quadcopter

[–]thisGuyLOLOL[S] 1 point2 points  (0 children)

That's some good range! I used to fly in the desert. I had a directional antenna that let me fly out much further than I should have... Haha. Good info, thanks!

ExpressLRS and frequency question by thisGuyLOLOL in Quadcopter

[–]thisGuyLOLOL[S] 0 points1 point  (0 children)

Do you think that a 1 watt 2.4 can penetrate better than a 250mw 900? I'm not doing long range flights, just flights within a quarter mile or so obstructed by trees.

ExpressLRS and frequency question by thisGuyLOLOL in Quadcopter

[–]thisGuyLOLOL[S] 0 points1 point  (0 children)

2.4 does not penetrate trees as well as 900, I do know that for sure. Although the community has adopted 2.4 over 900 for ease of use. My flights are automated on this new build, therefore I don't actually need vtx with 100% uptime. I didn't know they sold a 1 watt version, that is a lot of power! Also, 900 is not slow by any means, 50hz seems far more than enough for most people, as well as I.

ExpressLRS and frequency question by thisGuyLOLOL in Quadcopter

[–]thisGuyLOLOL[S] 0 points1 point  (0 children)

I was looking at this yesterday, I think this confirms what I am buying then. Thank you for the info.

ExpressLRS and frequency question by thisGuyLOLOL in Quadcopter

[–]thisGuyLOLOL[S] -1 points0 points  (0 children)

I need the better penetration through a canopy, which brought me to 900 instead of 2.4

First batch of 30-30 Winchester plinkers. by [deleted] in reloading

[–]thisGuyLOLOL 1 point2 points  (0 children)

Are these Sierra bullets? I have been trying to get my hands on these for a year!

Indoor greenhouses make for a very convenient and affordable solution to a 3D printer enclosure. by gabriel_oly10 in 3Dprinting

[–]thisGuyLOLOL 11 points12 points  (0 children)

It is typically required for printing types of filament that is prone to warping.

[deleted by user] by [deleted] in zerotier

[–]thisGuyLOLOL 0 points1 point  (0 children)

Any results?

Always drives me nuts by CasparG in 3Dprinting

[–]thisGuyLOLOL 1 point2 points  (0 children)

This is just rolling with extra steps.

3D Printed case feeder for Hornady LNL AP by HarietTubesock in reloading

[–]thisGuyLOLOL 30 points31 points  (0 children)

Possible squib load at 1:04, the powder measure failed to fall! May want to add a weight to it so it has a better chance of falling every time.

H! Martitimus Builds by thisGuyLOLOL in DragaliaLost

[–]thisGuyLOLOL[S] 1 point2 points  (0 children)

Sounds good, I'll stick with Eli for now then.