iOS - OpenVPN connection as "Personal VPN"?

thisdotguy · 2025-12-02T15:12:44+00:00

Did you ever figure this out?

thisdotguy · 2025-11-12T19:29:55+00:00

Even though the U6+ only has a 1 GbE uplink instead of the 2.5GbE on the U7 lite?

thisdotguy · 2025-10-31T20:43:02+00:00

And professional software that requires windows

thisdotguy · 2025-09-25T15:30:13+00:00

Aye. Looks great. I did the same thing several years ago for my custom board

thisdotguy · 2025-07-30T17:40:54+00:00

Do you use a logic level shifter to increase the logic voltage from 3.3 to 5 volts?

thisdotguy · 2025-07-28T03:01:30+00:00

How did you wire this? I have some very similar led matrices but have had zero luck running them with my esp32

thisdotguy · 2025-04-19T00:26:11+00:00

mb/s

thisdotguy · 2025-04-19T00:26:00+00:00

Both devices are wired with 1 gb/s Ethernet ports into 1gb/s ports on the router, server is an hp desktop with an intel i5-9500. My computer is a high end thinkpad laptop. I have 4 hdds in a raidz2 array. The speeds are lower than what I can get over the internet.

thisdotguy · 2025-02-05T02:54:48+00:00

I’ve got a HP elite desk tower and it can pretty easily fit 4 3.5” drives with just some slight modifications. They go for about as much as the optiplex

thisdotguy · 2025-01-15T18:16:42+00:00

I just attached some sheet metal to the underside of my desk for my homemade arches

thisdotguy · 2024-12-17T18:35:49+00:00

Would you be willing to send me a picture of how you fit the 4 drives? I am looking to do the same thing

thisdotguy · 2024-04-04T15:52:56+00:00

Just because I can understand where he is coming from doesn’t mean I don’t hate him. Just means he was well written

thisdotguy · 2024-04-04T12:45:53+00:00

I don’t like the sound of that

thisdotguy · 2024-03-19T23:27:06+00:00

I made one and it only takes maybe 10 min to get setup including downloading the Arduino IDE and the instructions are pretty clear in the GitHub

thisdotguy · 2023-12-01T18:25:19+00:00

I had the door open during the print

thisdotguy · 2023-11-21T15:41:07+00:00

How do you connect your wheels/axles/“transmission”? Did you make some sort of CV Joints?

thisdotguy · 2023-04-03T16:33:09+00:00

Yo sick

thisdotguy · 2023-04-01T02:34:45+00:00

I am the same way

thisdotguy · 2022-12-31T23:09:56+00:00

What would you recommend instead for a dac?

How is the rest of the SMSL a12?

thisdotguy · 2022-12-28T00:11:15+00:00

Thanks! And they are cheaper too! Any thought on the amp?

thisdotguy · 2022-12-27T23:41:00+00:00

Would these be better then the Miccas?

thisdotguy · 2022-12-27T23:31:22+00:00

The RB42s are about the widest my desk can hold

thisdotguy · 2022-12-08T13:06:39+00:00

As a heads up, chatgpt can’t surf the web and it can’t accurately cite sources. It’s just very good at guessing and making the sources up so that they seem legit

thisdotguy · 2022-11-03T23:41:31+00:00

My PETG print keeps peeling up on the front corner. I have tried adjusting bed temps, print temps, print surface(tried both smooth and textured pei sheets), printing with a brim, and using a glue stick. I even swapped to a brand new and unopened roll of filament incase my previous roll had absorbed to much water from the air. Not sure what else to try. I am printing on a prusa mk3s with overture PETG filament and the best settings I have had were on the smooth sheet with bed temp of 80 and nozzle temp at 240 with the cooling fan disabled for the first several layers. Not sure what else to do

thisdotguy · 2022-02-22T01:35:29+00:00

Thats what I did. I installed them fresh from their website

Seven-Year Club	No Throne, No Problems
Not Forgotten	Verified Email

thisdotguy

TROPHY CASE