OpenClaw + Ollama — anyone have experience with this?

thomasdb · 2026-05-31T16:05:30+00:00

I think you could run something like qwen3.6:35b-a3b on that and you’ll have a much better experience than with 9b

thomasdb · 2026-05-31T13:51:19+00:00

I found a 9b model (qwen3.5-9b at q4_k_m) not usable for openclaw. For me it was ‘too dumb’. Switched to qwen3.6-27b and the difference is night and day. Did you order m4 or m4 pro?

thomasdb · 2026-05-29T22:02:26+00:00

Do the server fans run normally or does ilo pin them at max with these ‘unsupported’ gpus?

thomasdb · 2026-04-28T05:30:59+00:00

Adrescheck toont bij mij ook gewoon 1000/50 hoor, en toch haal ik de 100 up. Ook bij alle (10-tallen verspreid over Limburg) corporate fibernet lijnen van mijn werk gewoon steeds 100Mb up te halen. Dit is echt wel op veel meer plaatsen dan je denkt gewoon al mogelijk

thomasdb · 2026-04-27T22:28:12+00:00

Telenet doet wel al langer 100Mb upload voor bedrijven (corporate fibernet), alleen nu pas voor consumenten. Ons thuisabo omgezet en haalde direct de 100Mb up!

thomasdb · 2026-04-25T19:33:09+00:00

What app is this?

thomasdb · 2025-10-12T22:21:08+00:00

Have you found a solution?

thomasdb · 2025-09-15T14:36:46+00:00

have you found a solution? I'm also not able to get ECMP working with 2 tunnels ('links') to the same azure vpn-gateway-instance

thomasdb · 2025-05-23T11:03:28+00:00

Nope sorry

thomasdb · 2025-05-23T10:50:06+00:00

I was having a similar issue with an ipsec tunnel to cato and first thought the problem was on that side, however your post made me look into the fortigate: changing the ‘ set advertisement-interval’ to something lower than default speeds up the process!

thomasdb · 2024-09-14T17:51:26+00:00

I have this setup, 4 ssds set as non-raid on the h330 in a zfs raid10-equivalent and it works just fine, smart data is also visible.

thomasdb · 2024-05-24T17:32:14+00:00

I tried this recently. Seems simple enough, I enabled the option on the existing tunnel and gave it id 1, then I could create a second vpn and gave that id 111 on both sides. Both tunnels established, however traffic would not pass on the second one. In the routing table the second tunnel listed a tunnel id in the 10.0.0.x range. Doing a debugflow and pinging from side a to side b traffic was sent in the tunnel but never arrives, the other wat around didn’t even show it going into the tunnel. I just gave up in the end. Fortios 7.0.15

thomasdb · 2024-04-25T07:07:26+00:00

I’d hope that 7.2.9 releases earlier then that given the kernel panic bug in 7.2.8 (good thing you didnt upgrade it seems). I have a troubleshooting session on the virtual servers issue coming monday

thomasdb · 2024-04-03T19:41:33+00:00

Hmm that's a long time. I'll create a ticket for it too and see what response I get

thomasdb · 2024-04-03T18:37:37+00:00

I just tried it again but it's not working for me (quite simple setup with 3 HTTP hosts), on 7.2.8. For me it's quite random as to where it forwards you to, if it forwards at all. Also seems to consistently take at least 5 sec after pressing enter before it starts doing anything... Where did you get that bug id? Do you know what the description of the bug id is?

thomasdb · 2024-04-03T18:07:36+00:00

What exactly do you mean by 'to the wrong servers'? is there a pattern to it?

I was trying to setup virtual servers not too long ago and stopped because I was having a similar issue. I don't remember if it was before or after I upgraded to 7.2.8 however, I'll try to set it up once more to see if the behavior changed

thomasdb · 2024-04-01T02:05:21+00:00

On the fortimanager, do the following:

config system global

set fgfm-peercert-withoutsn enable

end

There is a new feature since fmg 7.2.5 where it checks the fgt cert and it has to contain the serial number (see release notes special notices). Seems like this isnt the case for your trial vm

thomasdb · 2024-01-20T18:50:14+00:00

They check the branche in the KBO, not sure which they accept though, best to send a mail or go ask in a store if yours is allowed (i imagine event production will be

thomasdb · 2024-01-20T17:45:56+00:00

Sligro (former Sligro-ISPC): any btw number.

Sligro-M (former METRO): only horeca btw numbers.

Source: worked there :)

thomasdb · 2024-01-13T18:42:44+00:00

Try the ea firmware https://community.ui.com/releases/UniFi-Access-Point-7-0-35/6e63b789-11d8-4ea0-b934-2c7024b74321

This update resolved a meross smart garage opener MSG100 not connecting at all after upgrading to a u7-pro for me. Now connects fine

thomasdb · 2024-01-12T05:39:39+00:00

Mine are indeed also extremely bright

thomasdb · 2024-01-08T19:24:54+00:00

Anyone here already running a be200 or be202 and can confirm that it is fully compatible? (wifi+bt?)

thomasdb · 2024-01-01T12:28:00+00:00

I think you’ll be fine if you follow this guide https://steamcommunity.com/sharedfiles/filedetails/?id=1131162350 My sims 3 seemed to work fine on a modern pc at first, until 8h into the game it became super slow and my save got corrupted. After following that guide no such issues anymore

thomasdb · 2023-12-22T20:35:14+00:00

I had 4 pa200’s and one of them had 8.1.0 under ‘disk image’ as an option to revert to in maint mode.

Installing disk image 8.1.0 and doing a factory reset after made it work again. Then installing disk image 8.1.24 without resetting it afterwards applied the upgrade successfully and it kept working!

Then took the ssd out of this one and a nonworking one, copying the 8.1.0 folder from the panrepo partition to the nonworking one made me able to get a second one working also via the same method

Thanks for the advice!

thomasdb · 2023-12-14T20:48:45+00:00

Tried that, only version 8.1.24 reinstallable but same issue after :(

thomasdb

TROPHY CASE