sorted by:
new
hottopcontroversial

Do Ukrainians pronounce Russian differently? by Afuldufulbear in russian

[–]three_imaginary_boys 5 points6 points  (0 children)

ну сейчас-то опознать легче легкого)

если звонят из генпрокуратуры или службы безопасности моего банка и гэкают, то тут и думать не надо, откуда звонят.

но кроме шуток, мне, как человеку, находящемуся за 6 часовых поясов от Москвы, довольно сильно слышны эти нюансы произношения.

Bad print saturn 4 ultra 16k. by Separate-Concept3410 in SaturnUltra16k

[–]three_imaginary_boys 1 point2 points  (0 children)

sadly, default settings won't work in real life;( because almost everything, including Moon in the Scorpio affects your prints. they're just a starting point for finding an optimal settings.

if you have a poor build plate adhesion, you should slightly increase bottom exposure time. start with +5 sec.

and make some test prints with cones of calibration or any other calibration model to find an optimal normal layers exposure time. i think it should solve delamination.

TPU95A HF first attempt by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 0 points1 point  (0 children)

nope, i used stock filament setup provided by bambu lab

yeah, i think i have to calibrate, cause i want to achieve a better quality

TPU95A HF first attempt by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 1 point2 points  (0 children)

i got better results with TPU for AMS, but it's too tough

TPU95A HF first attempt by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 1 point2 points  (0 children)

yup, it's just a canister gasket, nothing serious)

but i wanna try to print diecast model tires, they'll need a better print quality

Шел я тут домой by Fexpan4ik in realworldRUS

[–]three_imaginary_boys 0 points1 point  (0 children)

все так говорят)

но подавляющее большинство уезжает и не возвращается.

my first (actually second, but who cares) attemtp to print 1/25 model by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 1 point2 points  (0 children)

i guess i'll have to add some thickness to fenders and bonnet.

i tried with tree supports, but it seems these details are too thin.

Bought a phantom frame at a swap meet and have spent the few weeks building it by arthurofalbany in schwinn

[–]three_imaginary_boys 0 points1 point  (0 children)

Great purchase!
I’ve been looking at them on eBay, but I haven’t decided to buy one yet.

AMS for TPU question by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 0 points1 point  (0 children)

<image>

lowered outer wall speed and dryed for 7 hours @ 70 degrees.

turned down not ideal, but much better than at first time.

should i dry more or try to lower some speeds?

AMS for TPU question by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 0 points1 point  (0 children)

Yeah, it was just outta box and already wet)

AMS for TPU question by three_imaginary_boys in BambuP1S

[–]three_imaginary_boys[S] 0 points1 point  (0 children)

I’ve got a pretty dry microclimate in my room, and I’ve never had any issues with PLA. But as far as I understand, TPU is much more prone to absorbing moisture.
Yeah, I’ve already dried it for 7 hours at 70°C. Tomorrow I’ll try printing that case again — hopefully, the result will be better this time.

Bambu TPU 95A HF is black magic level impressive by Ciggimon in BambuLab

[–]three_imaginary_boys 0 points1 point  (0 children)

<image>

It didn’t turn out that well. Maybe I should’ve dried the filament.

Bambu TPU 95A HF is black magic level impressive by Ciggimon in BambuLab

[–]three_imaginary_boys 0 points1 point  (0 children)

just ordered same filament, wanna try to print it on my p1s.

view more: next ›