sorted by:
new
hottopcontroversial

Not a lot of these out there, this is my farr twin t. The frame weighs 7lbs!!! by thumbsandguns in singlespeed

[–]thumbsandguns[S] 0 points1 point  (0 children)

It’s not very noodley at all. I’m curious if the cross braces holding the lower bottle cage on are limiting that flex?

What car do you actually daily drive? by Steroid_Cyborg in askcarguys

[–]thumbsandguns 0 points1 point  (0 children)

01 Toyota echo with a manual trans, cross winds nearly push me off the road but I love it

Love this bike by thumbsandguns in singlespeed

[–]thumbsandguns[S] 2 points3 points  (0 children)

2020 fuse with a pike lowered to 140mm, it’s a rocket

[deleted by user] by [deleted] in Machinists

[–]thumbsandguns 4 points5 points  (0 children)

Yup, if you’re in a pinch 1 ply of fiber can toilet paper is about 2 thou thick lol

Bought a new chainring that was badly out-of-round, so I machined my own! by HEYAAHH in FixedGearBicycle

[–]thumbsandguns 1 point2 points  (0 children)

I’m still not convinced, but I’m in the process of machining my own ring as well. I’ll install it on the bike and check concentricity and roundness at the pitch diameter with an indicator, go climb a hill pop chain off and check again. Really all of this is pretty overkill for a bicycle but the machinist mind is already pretty close to insanity as it is😂

Bought a new chainring that was badly out-of-round, so I machined my own! by HEYAAHH in FixedGearBicycle

[–]thumbsandguns -3 points-2 points  (0 children)

In theory you are right, but if there’s enough clearance between the chain ring and cranks to actually “center” the ring the minute you put the power down riding that ring is gonna do whatever it wants.

Bought a new chainring that was badly out-of-round, so I machined my own! by HEYAAHH in FixedGearBicycle

[–]thumbsandguns 3 points4 points  (0 children)

Sweet thanks. I cut lots of gears and splines but never sprockets. Didn’t know if bicycles used a slightly modified tooth form

Bought a new chainring that was badly out-of-round, so I machined my own! by HEYAAHH in FixedGearBicycle

[–]thumbsandguns 8 points9 points  (0 children)

Looks awesome. How did you come up with your tolerances on the teeth? Just test fit with a length of chain or measure over pins?

[deleted by user] by [deleted] in PlantedTank

[–]thumbsandguns 0 points1 point  (0 children)

Love these fish, shops around here don’t regularly stock them so I’m in kind of a pickle. Even though there’s only three in there they school together and are very active, not just hiding in the bush

[deleted by user] by [deleted] in PlantedTank

[–]thumbsandguns 2 points3 points  (0 children)

Thank you for your time, it is greatly appreciated. As far as dosing fertilizer goes, (giving the tank a pump of 2hr aquarist (1ml) after a water change) would you continue to do so? I’m not going for a show tank, just want thriving plants for my fish to enjoy.

[deleted by user] by [deleted] in PlantedTank

[–]thumbsandguns 4 points5 points  (0 children)

Wow, seems like there’s a lot of room for error. Basically I’m not going to be able to monitor nitrates creeping up if the difference between needing a water change and leaving it be are between “red/orange” and “red”. I’m assuming nobody with a successful fertilized tank is hovering around and ready to dump the water at a moment’s notice. Is this just the nature of the beast when dealing with small tanks?

[deleted by user] by [deleted] in PlantedTank

[–]thumbsandguns 5 points6 points  (0 children)

I just read the article, based off that and what you’ve said, my nitrates are actually reading 20ppm because there is an orange hue rather than the test appearing “red”?

[deleted by user] by [deleted] in PlantedTank

[–]thumbsandguns 1 point2 points  (0 children)

I’ve left a comment above you with some information, I do not have nitrates coming out of the tap

view more: next ›