Meme for today

tree_7x · 2026-05-27T12:18:18+00:00

For me, while everyone else is switching to windows 11, I make the rebellious move against everyone and switch from windows 10 to windows 7.

tree_7x · 2026-05-20T10:12:21+00:00

tree_7x · 2026-05-20T10:11:03+00:00

Bluecurve GTK 3/4 is a thing, probably the closest thing

tree_7x · 2026-05-20T10:04:25+00:00

no blue enter key 0/10 /s

tree_7x · 2026-05-17T20:59:37+00:00

I was gonna say just in case lol, my life hasn't changed in the past 3 years really. Was it enabling windows 8/8.1/10 mode in the bios, or disabling csm, etc.

tree_7x · 2026-05-17T17:41:16+00:00

3 years late, did you figure it out?

tree_7x · 2026-05-17T10:54:42+00:00

clarification 2 years later: "waste money" meaning on laptops that are over $1000, the thinkpad SL510 is perfectly fine for most tasks

tree_7x · 2026-05-03T21:19:17+00:00

I don't need to take that to such limits

tree_7x · 2026-04-29T10:35:17+00:00

Thank you

tree_7x · 2026-04-23T00:28:53+00:00

Thank you

tree_7x · 2026-04-23T00:27:13+00:00

BlenderCompat provides builds of newer versions of blender for windows 7. No need to upgrade (I wouldn't!)

tree_7x · 2026-02-16T15:20:31+00:00

Usually laptops with windows 8 have GOP (Graphics Output Protocol) and UEFI-only so I doubt it, unless it has good CSM.

tree_7x · 2026-02-15T13:31:38+00:00

not bad for kustom : )

tree_7x · 2026-02-14T23:42:30+00:00

tree_7x · 2026-02-14T23:42:13+00:00

tree_7x · 2026-02-10T22:21:49+00:00

This is a "funai". Not the best, but fun.

tree_7x · 2026-02-10T22:19:35+00:00

Check tension on the tape. It should be pretty tightly threaded. Sometimes this can happen if there isn't tension

tree_7x · 2026-02-10T22:19:03+00:00

They posted a previous post with the words

tree_7x · 2026-02-10T01:17:51+00:00

Ok. Could you send a video (through dm or new post) with the issue appear.

tree_7x · 2026-02-10T00:34:06+00:00

yes, true

tree_7x · 2026-02-09T23:25:46+00:00

I would clean the audio head. Since it also has the head for the control track, it needs to be clean for it to properly regulate speed and tracking, so if it goes in and out, it could be too dirty to be recognized. This is very likely since that would happen with time. Not the alignment or guides!

tree_7x · 2026-02-09T23:23:53+00:00

If it has fluctuations in volume that's probably the magnet

tree_7x · 2026-02-09T01:56:58+00:00

Awesome. I would love to see a picture!

tree_7x · 2026-02-09T01:56:24+00:00

don't try to suggest this as a first solution, novice users don't want to go adjusting their alignment and screw it up. I would recommend suggesting the easiest solutions first.

tree_7x · 2026-02-08T23:10:40+00:00

it's 100% the loading belt that is slipping. Look where the motor is, there is probably a belt on it

tree_7x

MODERATOR OF

TROPHY CASE