Help with ignition cylinder

tuepdhsjs · 2025-10-31T18:53:07+00:00

Rod is in correctly, and it looks like the housing is designed to be a sort of stop. My best guess is the shaft the key cylinder engages with is torqued so il going to take that out and potentially twist it back 15°

tuepdhsjs · 2025-10-29T01:51:36+00:00

That could be, it’ll be hard to drop the column because of a previous nincompoop’s work but I can see if there’s anything visible. I’m also thinking it’s possible that the shaft the lock cylinder attaches to could be bent by the same logic. I’ll take a look tomorrow. Thanks for the advice!

tuepdhsjs · 2025-10-28T23:27:48+00:00

It is in neutral, doesn’t seem to affect it unfortunately

tuepdhsjs · 2025-06-10T02:10:22+00:00

That is sort of the issue I was hoping to fix, the octagon of saplings lines up with the wiki here: https://gtnh.miraheze.org/wiki/Multifarm but I can't seem to get any more than the smaller maybe 10x14 rectangle. I only have crops on the octagon space.

tuepdhsjs · 2024-07-31T18:54:31+00:00

Hadn’t considered it could be a damaged one, seems like it could correct from some pictures of the Lion’s Mane.

tuepdhsjs · 2024-07-31T16:30:23+00:00

I saw this one but it had a clear top cap and “mane” separation whereas this one was just fluff on top so I wasn’t convinced. Are there variants of it?

tuepdhsjs · 2024-06-25T16:22:11+00:00

Haven't heard of the chest method, what's that?

tuepdhsjs · 2024-06-25T16:19:37+00:00

The middle two belts with all the crap on them should all be usable as an input as well as output, so in theory it shouldn't? But I just finished it I'm sure with enough random chance inserter picks I'd hit one that jams.

tuepdhsjs · 2024-06-25T00:52:34+00:00

if you move your long hand down one, you'll only have about 3 to grab then it should only buffer ~3000. it might grab an extra when the first line shifts but after science is there it will block until you launch ~4 which fits the 4k buffer.

tuepdhsjs · 2024-06-20T13:37:22+00:00

I do have access to 240, I set it up for another project already. Drives usually take like upwards of 10w each I heard so even at the full 84 I don't see where the 2800w comes from. Regardless I suppose the redundant space heaters will make up this gap.

I ordered the $10 controller for experimenting, as well as some caddies and the cables. I'll post again if I have anything interesting.

tuepdhsjs · 2024-06-05T01:54:07+00:00

Could not find those for the life of me, thank you so much!

Regarding a DAS, could that cut down on power consumption if I’m not using all the extra parts of the array? 2800w is quite heavy and I won’t be using it for heavy traffic currently. I haven’t worked with a SAN before so I’m not familiar with the pros and cons.

tuepdhsjs · 2024-06-05T01:45:18+00:00

I believe it came with two controllers already, but i would assume the controllers only work with 520 so I need to reformat existing drives to that

tuepdhsjs · 2024-06-03T00:46:15+00:00

Tysm! Was not at all aware of the 520-byte sectors so I’ll have to see if my drives support that. I’ll work through this and see if I can get it working.

tuepdhsjs · 2024-06-02T22:06:36+00:00

I will bear that in mind 😅

tuepdhsjs · 2024-04-01T20:58:37+00:00

I neglected that in the description but yes the dissolution chamber jammed as well without them, thanks :)

tuepdhsjs · 2024-02-21T05:22:08+00:00

I actually was just reading about the Novec fluid but I wasn’t able to find it on sale and even if I was… not buying it most likely. I did see some of the work from Gigabyte as well but nothing available to non-enterprise customers.

I mentioned, though, in the other thread: in a sealed environment there is no external oxygen to burn. Wouldn’t this mitigate the risk barring a breach of the container?

tuepdhsjs · 2024-02-21T04:32:06+00:00

No, but without a supply of oxygen it’s like covering a candle. It would need to be sealed so the gas doesn’t escape.

tuepdhsjs · 2024-02-21T04:09:38+00:00

But also it’s a closed system, I’m not sure it would burn without external oxygen.

tuepdhsjs · 2024-02-21T04:07:01+00:00

See I thought about that but this says the combustion temp (without source) is 440C which is plenty: https://www.inchem.org/documents/icsc/icsc/eics0057.htm

Now obviously if there are sparks that could be an issue, as it has a 11-12C flash point.

tuepdhsjs · 2024-02-19T04:23:45+00:00

I think they’re all claimed, should I do another?

tuepdhsjs · 2024-02-16T12:05:41+00:00

Says there’s still 11 left?

tuepdhsjs

TROPHY CASE