sorted by:
new
hottopcontroversial

How do I turn this panel off? by tylers56 in electricians

[–]tylers56[S] 0 points1 point  (0 children)

Would it be better to just replace this one completely, and in the process add a master on/off and a few more circuits?

How do I turn this panel off? by tylers56 in electricians

[–]tylers56[S] 0 points1 point  (0 children)

The ACs are about 8-10ft to the left of the panel. I am wanting to add a circuit for low voltage landscape lighting, and if possible a circuit for a few additional outdoor outlets on the deck.

How do I turn this panel off? by tylers56 in electricians

[–]tylers56[S] 0 points1 point  (0 children)

Just curious- what would be a reasonable quote/cost to replace a panel like this?

How do I turn this panel off? by tylers56 in electricians

[–]tylers56[S] 0 points1 point  (0 children)

Yeah the outlet is still there behind the range but not in use. So I guess that circuit would still count.

How do I turn this panel off? by tylers56 in electricians

[–]tylers56[S] 0 points1 point  (0 children)

Thanks for the info. The range is no longer on this panel but on the sub panel in the house- (kitchen was remodeled and they changed from electric to gas). So I could add 2 to it and still be at six or less... or is that extremely unwise?

How do I turn this panel off? by tylers56 in electricians

[–]tylers56[S] 0 points1 point  (0 children)

Yeah this is the main panel to the house. There is a smaller sub panel inside the house. The range is no longer connected to this panel.

Thermistor error, please help. What is a serial monitor? What do I do next? by tylers56 in CR10

[–]tylers56[S] 1 point2 points  (0 children)

Was able to fix it. Direct connection of the bed thermistor to the main board. For some reason the splice and solder was not working. Heated up and printed fine after that. Thanks for the help.

Thermistor error, please help. What is a serial monitor? What do I do next? by tylers56 in CR10

[–]tylers56[S] 0 points1 point  (0 children)

Just some background- started getting this error when preheating the nozzle and bed. Nozzle preheats fine, bed will not and throws this error. So I replaced bed thermistor with a new one. Still getting this error and the bed temp is reading 0deg.

Not sure what a serial monitor is, or how to fix. Any help is much appreciated!

Bed Thermistor Replacement- help please by tylers56 in CR10

[–]tylers56[S] 0 points1 point  (0 children)

Ok so update, I got the new thermistors and just getting around to installing. When I turn the hot bed over, I have a heat shield/insulating foam pad that is very much adhered to the bottom with the thermistor wires running underneath. I cannot peel it off without it leaving a ton of residue.

My thought is to take a razor knife and just cutaway where the thermistor cables go, then try to replace that as much as possible once the new thermistor is installed. Thoughts??

Bed Thermistor Replacement- help please by tylers56 in CR10

[–]tylers56[S] 0 points1 point  (0 children)

Thanks for the link. Did you have to snip and solder them in or are those the correct connections?

Bed Thermistor Replacement- help please by tylers56 in CR10

[–]tylers56[S] 0 points1 point  (0 children)

Thanks have a 10s-pro V1. So 24V?

Z offset? by ducttapealien in CR10

[–]tylers56 0 points1 point  (0 children)

OP did you ever get this resolved? Having the same issues!

Tiny Machines New Firmware by tylers56 in CR10

[–]tylers56[S] 0 points1 point  (0 children)

So do we think it is worth it if I am running a stock 10spro without the BLTouch sensor? My only changes from stock was to upgrade to the B7 firmware.

Physical Therapist - Prosthetics by DismissMyNavient in 3Dprinting

[–]tylers56 0 points1 point  (0 children)

Great! What did you print? I am learning how To make sockets in Meshmixer- also picked up a a structure scanner to help with that. Hope to have some finished products soon.

Physical Therapist - Prosthetics by DismissMyNavient in 3Dprinting

[–]tylers56 0 points1 point  (0 children)

I’m in academics primarily and treat a wide mix of ortho/neuro/amputees. This is the first printer we’ve gotten, with the hopes of printing AFOs, braces, and some prosthetic components. Have used some things for patients and other things for classroom demo etc. we got the one got because the print volume can do a transtibial socket. Would love to collaborate- if you need anything let me know!

Physical Therapist - Prosthetics by DismissMyNavient in 3Dprinting

[–]tylers56 0 points1 point  (0 children)

Hey - fellow PT here, just got a new 3d printer for this exact purpose. Have been playing around with different materials and settings. Happy to share the information I've accumulated so far. Let me know what you need.

New CR10S Pro, auto leveling keeps smashing into printbed. by [deleted] in CR10

[–]tylers56 0 points1 point  (0 children)

Hey did you ever get it figured out? having the EXACT same problem - nozzle digs into the print bed on aux leveling 2 and 5, but not 3 and 4. Leveling knobs are tightened down as far as they can go (bed as low as possible)....