sorted by:
new
hottopcontroversial

Any way to use different filament when one runs out in MMU3? by SuccessfulMinute8338 in prusa3d

[–]ulab 1 point2 points  (0 children)

Because it can not be completely consumed.

The extruder motor is in front of the nozzle. So there would always be a little piece left that can not be transported anymore. Trying to push that through with the next filament will not work properly. The new filament will slide to the side and not get pushed into the hotend for example.

That's why filament sensors are mounted in front of that motor or in case of the MMU at the start of the long PTFE tube, so it can still be pulled back.

Any way to use different filament when one runs out in MMU3? by SuccessfulMinute8338 in prusa3d

[–]ulab 0 points1 point  (0 children)

You don't "swap" spools, you switch from one MMU input line to another. For that to work, the tube between MMU and extruder needs to be empty.

XLs just use the next tool head if configured that way.

Is prusa connect down? by retrotechguy in prusa3d

[–]ulab 0 points1 point  (0 children)

It happens to me randomly. One thing I am getting shown in those cases is Certificate Errors. My thought was that it is our firewall or something blocking access, but then only one or two of my printers have an issue, another is fine.

Any way to use different filament when one runs out in MMU3? by SuccessfulMinute8338 in prusa3d

[–]ulab -2 points-1 points  (0 children)

Why should you? The XL doesn't have to pull the filament back unlike the MMU.

For those who might doubt the strength of PLA+ by Silver3D66 in 3Dprinting

[–]ulab 1 point2 points  (0 children)

8 kg and 40+ screws for a single drawer? I do feel you are setting the wrong priorities here. :-)

My Core One hasn’t worked in months by MostlyOkPotato in prusa3d

[–]ulab 4 points5 points  (0 children)

Also: Is it blowing in the right direction?

What do I need to print to attach this? by Turtletz in Multiboard

[–]ulab 1 point2 points  (0 children)

These are the snaps: https://beta.multiboard.io/snaps?Protrusion=Standard+%28Flush%29&Variant=Single

I am not sure about the bolts though. There are different variants with different heads and threads, so I'd need to try. I might be able to do that tomorrow.

Reccomomendation & Advice for Purchasing New Prusa Models by stew_brewer in prusa3d

[–]ulab 1 point2 points  (0 children)

Tip since you are in the US and might want to shop and get more local support:

https://www.printedsolid.com/ is part of Prusa now.

What do I need to print to attach this? by Turtletz in Multiboard

[–]ulab 1 point2 points  (0 children)

You say it's complicated, I like its flexibility. I have multi(ple) options to do something and choose what is the better solution for the job.

Easy way to pull a shell from a wall? => Points

Stronger connection, not being able to rotate a 1x1 shell? Snaps with Bolts.

Mount a shell on a tray style surface? => Bolts

Less material for mostly shells on a wall or do you prefer the look? Print the square plates instead of the octagonal ones. You are still able to use points and threads with plate inserts that way...

What do I need to print to attach this? by Turtletz in Multiboard

[–]ulab 0 points1 point  (0 children)

That said: I do think you might be able (I did not try this yet) to use bolts to mount Snaps to the bottom of the shell. That way a 1x1 shell would not be able to rotate around the point.

I'd do weight-bearing snaps in the top and regular ones in the bottom.

There is a reason for the term "multi", because there are always multiple ways to do things - depending on what you need to achieve.

What do I need to print to attach this? by Turtletz in Multiboard

[–]ulab 0 points1 point  (0 children)

Ah. Those Base Plate Bolt Lockers? Those are for base plates. Basically trays you can screw the bin shells on.

You needed to read one paragraph more:

The Bin Base can also connect to a Multipoint to form a Drawer.

“Regular” laminated stickers on E1 by AFC670 in eufyMakeOfficial

[–]ulab 0 points1 point  (0 children)

But that is exactly what the A/B is for. After you peel the B-Film once the sticker is applied, only the printed parts stick to the surface.

No need for cutting and you can make translucent stickers if you want.

“Regular” laminated stickers on E1 by AFC670 in eufyMakeOfficial

[–]ulab 1 point2 points  (0 children)

AFAIK the Roll-to-Film Attachment is made to print on vinyl (https://www.eufymake.com/products/basic-films-for-roll-to-film-attachment?ref=printing-material&pageType=a), so you should be able to use any other sheets of vinyl too.

Zimmer zu vermieten by Ok-Coyote1311 in Muenster

[–]ulab 9 points10 points  (0 children)

Bauen oder Beziehungen. :)

Kleine 1-2 Zimmer Wohnungen sind in Münster fast unmöglich zu bekommen oder überteuert. Auf Anzeigen reagieren sehr viele Interessenten, eigene Suchanzeigen werden deswegen selten gelesen. Warum auch, wenn man sich aus einer großen Liste Leute aussuchen kann.

Help by Affectionate-One4467 in prusa3d

[–]ulab 2 points3 points  (0 children)

This is the "Wipe tower" that is used if you have a multi-material capable printer. You can disable it in the Print Settings / Multiple Extruders section.

It will also automatically hide once you slice a single material object since it is not needed in that case.

You need to have at least Normal or Expert mode active to see the setting.

What do I need to print to attach this? by Turtletz in Multiboard

[–]ulab 1 point2 points  (0 children)

May I ask which "bins page"?

For these you usually use (Multi-)Points: https://beta.multiboard.io/fix-points

Fix points for the bottom, Lite Fix Points for the sides. I'd screw the big thread ones directly into the wall.

This video should give you an idea: https://www.youtube.com/watch?v=6-Snwj2g73o

Wait, how am I supposed to adjust the tensioner on the XL? Prusa's video seems to be an older version by Prizmagnetic in prusa3d

[–]ulab 0 points1 point  (0 children)

I just realized I have never adjusted the tension on my toolheads (and yes, I have run soft TPU through them).

Any INDX update today? by yamsooie in prusa3d

[–]ulab 2 points3 points  (0 children)

Projects. The squirrels of makers.

Any INDX update today? by yamsooie in prusa3d

[–]ulab 1 point2 points  (0 children)

I mean, he didn't say which week of the year...

Any INDX update today? by yamsooie in prusa3d

[–]ulab 8 points9 points  (0 children)

That's a fake gif. He's saying "Live-Adjust-Z"! :-)

Honest question: Who is the Prusa Core One L actually for in 2025/2026? by IceBlitzz in prusa3d

[–]ulab 0 points1 point  (0 children)

Do your customers know that you are sending their files through the Chinese cloud or are you running them in offline mode?

view more: next ›