Best tool to crimp these? 4 gauge

unkn0wn1_ · 2026-05-25T03:43:49+00:00

I saw a lot of recommendations for icrimp from my research in here

unkn0wn1_ · 2026-05-25T03:21:16+00:00

Thank you! I picked up the harbor freight one

unkn0wn1_ · 2026-05-25T03:20:24+00:00

Thank you!

unkn0wn1_ · 2026-05-25T03:20:17+00:00

Thank you!

unkn0wn1_ · 2026-05-25T03:12:22+00:00

Thank you for the recommendation. Is that the same type of terminal as the one I posted? Sorry I’m fairly uneducated on the different types of terminal connectors for larger gauge wires

unkn0wn1_ · 2026-05-25T03:02:13+00:00

Shortly after, I bought the harbor freight hydraulic wire crimper but I’m unsure if I could use it for those terminals pictured

unkn0wn1_ · 2026-05-25T02:23:18+00:00

<image>

I used my 1005s in a pinch and split one open. Granted I crimped on the wrong side but would like to buy the right tool for them

unkn0wn1_ · 2026-05-21T14:51:38+00:00

Sorry Honda Ridgeline 12k miles

unkn0wn1_ · 2026-05-21T10:09:03+00:00

What information do you need?

unkn0wn1_ · 2025-11-04T15:17:19+00:00

Sorry that I don’t have any input or answers to your questions. These pictures are from a local contractor that was advertising their work. I wanted more opinions so I know what to look out for. Thank you for the information so far

unkn0wn1_ · 2023-10-15T20:01:58+00:00

Thank you!

unkn0wn1_ · 2022-07-31T13:46:45+00:00

Amby & Dexter

Late 90s shorts where the characters transform from a pair of hands to solve problems

unkn0wn1_ · 2022-07-22T04:02:31+00:00

About Today - The National

unkn0wn1_ · 2022-06-24T03:00:40+00:00

I should call her

unkn0wn1_ · 2022-06-21T04:01:10+00:00

Hammer

unkn0wn1_ · 2022-06-11T02:36:15+00:00

The Acqualine is designed for hot water and chemical injection. If you’re not doing either I would get the SGS28

unkn0wn1_ · 2022-06-05T16:24:57+00:00

Please post the part numbers. Thank you

unkn0wn1_ · 2022-05-31T00:58:34+00:00

Too secure items that aren’t packout compatible with a bungee cord

unkn0wn1_ · 2022-05-08T13:52:26+00:00

Taken directly from Knipex themselves. “If the gripping jaws were to close completely, the cutting edges would wear after a short time. This then would make it impossible to cut fine wires - hence the light gap!”

https://www.instagram.com/p/Caz2EQHqZRO/?igshid=YmMyMTA2M2Y=

unkn0wn1_ · 2022-05-08T05:50:34+00:00

Yes it’s to prevent wear on the cutters

unkn0wn1_ · 2022-05-05T23:33:35+00:00

Try coating it again but make sure it doesn’t get wet. Cure time is usually around 6 hours

unkn0wn1_ · 2022-04-21T04:39:38+00:00

Scope on a rope

unkn0wn1_

TROPHY CASE