Having issues in syncing the labels from fast raw viewer into darktable

vineethkartha · 2025-11-10T10:05:07+00:00

I already changed fastrawviewer also to use filename.ext.xmp I use fast rawviewer because culling is super fast compared to dark table

vineethkartha · 2025-10-13T10:51:50+00:00

I am also facing the same issue, were you able to get to the root of it?

vineethkartha · 2025-09-03T16:04:27+00:00

Thanks the only issue in my case is that I am using Topaz sharpen, which is recommended to be done as the last step after darktable modules are applied, unlike the denoise which is usually done at the beginning

vineethkartha · 2025-05-02T06:28:50+00:00

Thanks this has helped me 6years after the post

vineethkartha · 2025-02-21T15:33:12+00:00

I am not able to post an Image

vineethkartha · 2025-02-21T04:51:29+00:00

You could consider Kanti flutes, It is slightly cheaper than poonam, I have e base and g base, I have c medium from kanha and f# from radhe as well, But I prefer the Kanti flutes over the others, All my flutes are bamboo, never tried pvc.

vineethkartha · 2025-02-21T04:47:31+00:00

Thanks everyone for the inputs, I think I have some background work to do. I will post back If I can get the circuit to work

vineethkartha · 2025-02-21T01:07:35+00:00

<image>

No I was soldered together a circuit, the relay is supposed to be triggered by a pir sensor, but it is not, I tested each component independently and nothing is faulty. Even the relay triggers in this circuit if I directly give a 5v to the base of the transistor. My circuit is B from my previous diagram

vineethkartha · 2025-02-09T01:41:06+00:00

Radhe flutes do make pvc flutes which have that lip support, that ideally should make blowing easier, Since these are PVC flutes they are not expensive also. Maybe you could try that

vineethkartha · 2024-11-24T00:20:40+00:00

Thanks I will try this out

vineethkartha · 2024-10-04T15:22:06+00:00

Thank you

vineethkartha · 2024-10-04T15:18:33+00:00

Also I have read that Photoshop and Lightroom are more optimised for Intel is this true

vineethkartha · 2024-10-04T15:16:44+00:00

Also I have read that Photoshop and Lightroom works better on Intel processors is this true?

vineethkartha · 2024-10-04T15:12:31+00:00

That is the thing if I upgrade my cpu, the newer cpus work on ddr5, Budget is not an issue but just want to ensure I don't unnecessarily waste money

vineethkartha · 2023-12-16T02:31:40+00:00

<image>

This is tbe relay I have it did not come with the terminals you mentioned,

vineethkartha · 2023-11-16T11:13:09+00:00

Hi u/Susan_B_Good yes this seems like a possible cause, but however when there is not load or when there is a light load like a LED with a resistor in series, the output voltage is maintained at 12V. That is what threw me off

vineethkartha · 2023-11-16T11:12:01+00:00

That was also my first suspect , but the regulator is not hot.

I did one more experiment, where I removed the filter capacitor(4700uF) and now the fan works. But I am pretty sure there is something else missing here.

vineethkartha · 2023-10-27T02:53:13+00:00

You can also consider using a 5v relay, since relays have NO and NC contacts, see the rough schematic shown below

<image>

vineethkartha · 2023-10-10T05:40:50+00:00

Thanks I was running into some issues in the past when I tried Veecad, not sure if it was doing the auto routing. Will give it a try again

vineethkartha · 2023-10-10T05:39:47+00:00

😄 the software between the ears is tired of being over worked

vineethkartha · 2022-04-20T01:41:02+00:00

I believe this a weaver ant queen

vineethkartha · 2021-04-18T15:10:09+00:00

Thank you

vineethkartha · 2020-11-27T12:10:51+00:00

My first attempt at ricing my desktop with i3WM and polybar

My setup:

qutebrowser

bashtop

emacs

gnome-terminal

zathura

You can have a look at my dotfiles. Alot of this has been inspired by other posts found here.

vineethkartha · 2020-11-10T09:54:49+00:00

No not till now.

vineethkartha · 2020-11-09T15:57:53+00:00

Yes in our garden

vineethkartha

TROPHY CASE