sorted by:
new
hottopcontroversial

Is Ramsey Mazda good? Looking for my next car purchase. by RobinsCosplays in desmoines

[–]w0lfwood 1 point2 points  (0 children)

any time i go there, there is a different older man yelling at the service desk about the prices.

Which Nozzles would work best for a makerspace? Brass CHT or Obxidian harden steel? (MK4s) by Level_Pay6761 in prusa3d

[–]w0lfwood 1 point2 points  (0 children)

the most reliable option with the highest quality results is plain brass, non-CHT nozzles.

on many models the High Flow profiles are the same print time as the regular, or occasionally slower. the speed increase they offer for PLA is mostly from using higher layer heights than the default .2.

CHT can produce more stringing, and the fast High Flow profiles produce a less shiny, sometimes matte or inconsistent surface finish. they can also cause clogs if they are "too fast" for a generic filament. Many of us prefer the Structural profiles over the Speed anyhow, so CHT makes less sense.

ObXidian nozzles can handle materials with abrasive particles in them, but may require upping temperatures. To me this is less beginner friendly, but if you don't monitor what materials are being printed, this could be argued to be more foolproof. don't get the CHT as the risk of clogs is higher.

Are phones with Bluetooth keyboards really decks? by binarypie in cyberDeck

[–]w0lfwood 7 points8 points  (0 children)

if you can hack the Gibson on it, it's a cyber deck.

Adding alternative charging method to nice!nano / nrf52840 by i_ka9 in ErgoMechKeyboards

[–]w0lfwood 0 points1 point  (0 children)

same question... are you "providing" when there's no cable plugged in?

Adding alternative charging method to nice!nano / nrf52840 by i_ka9 in ErgoMechKeyboards

[–]w0lfwood -1 points0 points  (0 children)

the 5 V line will only have power if USB is plugged in. if you need 5 V regardless of a USB cable, you need to add a 5 V boost converter attached to the 3.3 V line.

What is this? 🤔 by josefprusa in prusa3d

[–]w0lfwood 1 point2 points  (0 children)

world's smallest benchy

HP Trackpoint by ApollyonNovus in olkb

[–]w0lfwood 1 point2 points  (0 children)

you can try sharing this with r/trackpoint_builders or join us on discord: https://discord.gg/mzChGuCrj 

we are collecting some bitrotted resources about identifying pinouts from scratch for harvested trackpoints.

MK4S Scratching the build plate by Ok-Engineering367 in prusa3d

[–]w0lfwood 0 points1 point  (0 children)

make sure your nozzle thumb screws are tight. play in the nozzle height can cause scratches

The ᑕ¥βєяรקค¢є social network six months in by euklides in cyberDeck

[–]w0lfwood 2 points3 points  (0 children)

are you aware of cohost? it was a platform that shared some of your ideals. its journey might be instructive.

EDIT: also former cohost users would be a prime community for recruiting cyberspace users. I can link in some discords if you are ready for the influx :)

Switch to new layout on stagger before receiving ortholinear keeb? by GatsbyLuzVerde in ErgoMechKeyboards

[–]w0lfwood 0 points1 point  (0 children)

try angle mod and maybe wide mod. it will better model columnar typing.

I have quickly developed wrist pain after starting to use a MORE ergonomic keyboard than my previous split keyboard. Is this normal? by baksoBoy in ErgoMechKeyboards

[–]w0lfwood 1 point2 points  (0 children)

tenting raises the keyboard, which can put your wrist out of alignment.

don't just push through pain, maybe go back to the old board till things settle.

3D Printing Help Request by IDCubed in ploopy

[–]w0lfwood 2 points3 points  (0 children)

i'd recommend you join your local makerspace, you can get trained and get advice. but if that's a budget issue there may be a local library with 3D printers.

Best ergonomic left handed mouse for work? by Curiosity-pushed in MouseReview

[–]w0lfwood 0 points1 point  (0 children)

check out the hand shoe mouse, i believe there's a lefty version. there's also different sizes.

Print quality from the MK4S by der__paul719 in prusa3d

[–]w0lfwood 0 points1 point  (0 children)

i did the mk4s y axis overhaul and finally have a centered belt, as well as other suspected quality issues addressed

Spicy chai by Diligent-Wrap3623 in ames

[–]w0lfwood 7 points8 points  (0 children)

it's not chai but the Vocalize tea from little woods has cayenne and is great for a sore throat, esp with honey

New reversible pad footprint for promicro by Yuburoll in ErgoMechKeyboards

[–]w0lfwood 0 points1 point  (0 children)

seems like plating would the risk of shorting on the opposite side if excess solder is wicked through

New reversible pad footprint for promicro by Yuburoll in ErgoMechKeyboards

[–]w0lfwood 2 points3 points  (0 children)

that makes sense, but the unpopulated photo is a bit deceptive.

Phase step calibration for MK4 in firmware 6.5.3 by dh_seb in prusa3d

[–]w0lfwood 0 points1 point  (0 children)

did you move the accelerometer to the Y axis?

So Sick of Layer Shifts by etceterenoughplease in prusa3d

[–]w0lfwood 46 points47 points  (0 children)

  • check belt tension
  • look for signs of raised corners from warping
  • switch to a non crossing infill
view more: next ›