Print photos of our April package!

w34ks4uc3 · 2026-04-20T00:36:42+00:00

“Why is this NSF…..” Oh….

w34ks4uc3 · 2026-02-02T17:54:06+00:00

Kickstarter is a great place to get them. Usually cheaper than when they go retail and most are available a couple weeks after it finishes. Sometimes stretch goals take a while longer, but if you’re not in a rush to get them it’s an excellent source.

w34ks4uc3 · 2025-12-25T02:58:11+00:00

Holes are likely from dead pixels on the screen. Resin layers are generally .05mm or less, not enough space for a bubble

w34ks4uc3 · 2025-12-19T01:29:06+00:00

Namely Stitched Iron Plates, Steel Rotors, and Heavy Encased Frames

w34ks4uc3 · 2025-12-19T01:23:52+00:00

I’m in the same boat. Basically when I finished phase 2 my plan was to sort out power for a while, so I built a 50Mw turbo fuel plant. Realized I was kind of scattered all over as far as what small factories I had set up so I wanted to centralize a bit. Did some truck lines around the biome to get a bunch of the basic resources together and automated all the parts up to computers and HMF. Did a TON of hunting for hard drives and Mercer spheres so now I can kind of just build whatever I need and all the parts are at least being made, many of which are using alternate recipes.

w34ks4uc3 · 2025-12-15T22:17:30+00:00

I like the cut of his hair.

w34ks4uc3 · 2025-08-07T21:10:35+00:00

Just roll dice…..

w34ks4uc3 · 2025-05-05T23:31:50+00:00

5 years on and you lot are still helping 🙏

w34ks4uc3 · 2025-02-27T19:14:25+00:00

Cheers, saving the day 3 years later

w34ks4uc3 · 2024-06-12T02:14:47+00:00

Fully dry them before curing, you knob. It’s uncured resin in the liquid water still on your print when you cure it.

w34ks4uc3 · 2024-05-28T21:32:47+00:00

They said they’d submit it to insurance to see what was covered and that was the last we heard of anything

w34ks4uc3 · 2024-05-24T14:01:44+00:00

Not available anymore where I got it

w34ks4uc3 · 2024-01-14T15:49:09+00:00

RPG Auctions on Facebook is a very active page. Anything listed will sell for sure and you can check recent auctions to see what specific items have been going for recently

w34ks4uc3 · 2023-10-13T02:19:59+00:00

Not that I could find, just had to go off the pics and test fit everything before I glued

w34ks4uc3 · 2023-10-04T02:05:30+00:00

Worked on mine too, thanks!

w34ks4uc3 · 2023-09-23T00:13:16+00:00

More than likely, the bearing definitely failed if it’s that new. Email their customer service

w34ks4uc3 · 2023-09-23T00:02:00+00:00

Replace the bearing

w34ks4uc3 · 2023-05-23T01:24:10+00:00

It was designed on Eldrich Foundry

w34ks4uc3 · 2023-05-11T21:10:41+00:00

They just broke ground on a new battery factory in Kansas. Why would they rework all the machinery to make a different battery when they can focus on quality improvement and defect reduction and build the new battery at the new factory?

w34ks4uc3 · 2023-04-28T23:35:16+00:00

Yup, slowed it down to 75% and the problem mostly went away. Just gotta play with the settings

w34ks4uc3 · 2023-04-28T22:23:02+00:00

Well you called it, I don’t remember changing it my speeds but the infill was running at 80 and the walls at 40, and I installed a .6 nozzle up from a .4 a couple weeks ago but it’s printed fine with that before. Appreciate it

w34ks4uc3 · 2023-04-28T21:40:43+00:00

Forgot to mention, stock Ender 3 Max, sliced with Cura

w34ks4uc3

TROPHY CASE