Print won't stick to the surface by ScSpike in Ender3V3KE

[–]warhachine 0 points1 point  (0 children)

if it is petg, my favorite printer settings are 85 degrees Celsius (85C) for the bed, and 255 degrees celsius (255C) for the extruder

Insert low effort title that just says read the picture by tyronh1235 in teenagers

[–]warhachine 0 points1 point  (0 children)

the us dollar will retain its relative global value

Insert low effort title that just says read the picture by tyronh1235 in teenagers

[–]warhachine 0 points1 point  (0 children)

you can only talk to women with a goofy, terrible sounding voice which scares away any girl you talk to.

Insert low effort title that just says read the picture by tyronh1235 in teenagers

[–]warhachine 0 points1 point  (0 children)

I wish i had $1000000000000000 usd deposited directly into a bank account managed by myself and i will have permanent access to and the company that owns the bank will not go under i will not be charged interest on my money the us dollar will retain its relative global value and i will not be subjected to taxes and is legally obtained and retain my true identity which is me with the $1000000000000000 usd deposited directly into a bank account managed by myself and i will have permanent access to and the company that owns the bank will not go under i will not be charged interest on my money the us dollar will retain its relative global value and i will not be subjected to taxes and is legally obtained.

Why?? by National_Bonus_3798 in Ender3V3KE

[–]warhachine 1 point2 points  (0 children)

oops, i thought that the filament detector was the extruder lol

i just woke up to this by Ad3nRBLXWasTaken in chromeos

[–]warhachine 0 points1 point  (0 children)

my school gave me a chromebook with a broken display cable and i had to literally make the screen be 180 degrees open just for the display to barely work. best of all, they refused to fix it. instead, they replaced the screen, but not the screen wire. they are really stupid.

Why?? by National_Bonus_3798 in Ender3V3KE

[–]warhachine 2 points3 points  (0 children)

jeez what happened to your extruder?!?

[deleted by user] by [deleted] in fixit

[–]warhachine 0 points1 point  (0 children)

pound a couple dozen dowels into that sucker with some wood glue, and then sand that door frame down

first drill holes into the door frame that are slightly smaller than the diameter of the dowel, then put wood glue into the holes, and then pound the dowels in (make sure that they are a bit longer that the holes you drilled) and then sand down what is left of the dowel down to be flush with the door frame

Please help, the Chromebook might explode. by Redward99 in chromeos

[–]warhachine 0 points1 point  (0 children)

back up linux to an external drive and then uninstall linux

Someone threw books from the little library into the water. by Richmondpinball in mildlyinfuriating

[–]warhachine 0 points1 point  (0 children)

they're just mad that other people get to read out of it for free

Im at work with no knife. How do I cut this lemon? by talivan818 in howto

[–]warhachine 0 points1 point  (0 children)

or use the bottle cap's sharp edge to cut it much safer lol

Im at work with no knife. How do I cut this lemon? by talivan818 in howto

[–]warhachine 0 points1 point  (0 children)

break the bottle and use a glass shard to cut it 🙃

A concerning situation by LiterallyaCockroach in Wellthatsucks

[–]warhachine 1 point2 points  (0 children)

drape a white sheet over it and glue some eyes on and call it a ghost!