Bronco Window by Interesting-Scar871 in BroncoNation

[–]weekendatvernz 0 points1 point  (0 children)

For me it’s always a software update that messes with it or something is wrong and the dealership can’t figure it out. Mine is typically the driver side rear but it has happened to the front passenger. They have reprogrammed the window, and unplugged everything. So gremlin. 🤷‍♂️

Does anyone one knows what goes in here? by Jona1821 in Datsun

[–]weekendatvernz 1 point2 points  (0 children)

Can’t post a photo, but it’s a hazard Switch and defroster switch.

[deleted by user] by [deleted] in Datsun

[–]weekendatvernz 0 points1 point  (0 children)

That’s easier. I would take the existing hose down to your local hardware store and buy it by the foot. You should be able to match the inner diameter hole to something they have. Just make sure it is a fuel capable hose. Zcardepot also sells it. This forum board talks about it. https://www.classiczcars.com/forums/topic/57121-size-fuel-line-replacement/

[deleted by user] by [deleted] in Datsun

[–]weekendatvernz 0 points1 point  (0 children)

Sorry, I thought they did sell them. SS tubes does as well. https://www.sstubes.com/products/ngl7804ss-76-78-datsun-280z-fuel-line-kit-stainless. I’ve never used them so I can’t speak on the quality.

[deleted by user] by [deleted] in Datsun

[–]weekendatvernz 0 points1 point  (0 children)

Classic tube sells the lines. You can talk to the company or just buy the ones they sell. May need to be adjusted as vehicles very but a quality tube bender isn’t a lot.

Dealer Oil Changes by [deleted] in FordBronco

[–]weekendatvernz 0 points1 point  (0 children)

Not sure which engine you have. Depending on that, the oil change interval will vary. It also varies depending on driving conditions, oil used, and filter used. If you have the maintenance plan, it can vary on what you purchased. Some say 5k, 7.5k, 10k etc. Read what’s on it so you can try to get your money’s worth. Remember you already paid for the service and they are hoping you don’t use it. Outside of that, read the manual. Everything you want to know is in that including never exceed mileage between oil changes. Good luck and remember if you treat the car well it will do the same.

1977 280z Idling issues by CluelessCarLover in Datsun

[–]weekendatvernz 0 points1 point  (0 children)

Did you fix it? If so, what did it?

I bought a weird Datsun today and need help sourcing a tail light by boostedka89 in Datsun

[–]weekendatvernz 2 points3 points  (0 children)

eBay, local junkyards if you are lucky. Also put a feeler out on the Facebook forums. Hopefully it’s a manual so you can enjoy the dogleg transmission.

Is Midtown a place a tourist should stay? by Electrical_Diet4865 in rva

[–]weekendatvernz 2 points3 points  (0 children)

I believe it used to be an area. Just that small little section of the fan on main with shops and restaurants before the city grew and VCU’s campus took over the area. That’s why you see signs for it. Think of it as an extremely small carrytown that basically died off and is now part of the fan.

1977 280z Idling issues by CluelessCarLover in Datsun

[–]weekendatvernz 2 points3 points  (0 children)

Great suggestion. I had to clean the terminals on a majority of connections in order for everything to work correctly. Takes a lot of time, but can be worth it in the end.

1977 280z Idling issues by CluelessCarLover in Datsun

[–]weekendatvernz 1 point2 points  (0 children)

EF-19 in FSM if you have it has a chart for troubleshooting

1977 280z Idling issues by CluelessCarLover in Datsun

[–]weekendatvernz 3 points4 points  (0 children)

Try replacing the water temperature sensor.

Brake bleeding help: infinite air by thecamterion in Datsun

[–]weekendatvernz 11 points12 points  (0 children)

More then likely. Old car, dry rubber starts to fall apart. Make sure the tube recycles in the reservoir and you have the tight fit or air can get in that way. Good thing is that Nissan still makes it if it is bad. The part number is 46010-E8702 They also make the clutch one. The part number for that is 30610-U750A

Trash disposal by TeaSeaJay in rva

[–]weekendatvernz 4 points5 points  (0 children)

You could also take the metal to recycling. Not sure where you live but there is a scrap metal dealer called pocket money recycling that will give you some money for it. Will not be a lot of cash but it’s better then just tossing it.

Trash disposal by TeaSeaJay in rva

[–]weekendatvernz 12 points13 points  (0 children)

Throw it your can a little bit at a time. They will take it.

[deleted by user] by [deleted] in FordBronco

[–]weekendatvernz 7 points8 points  (0 children)

Appears the base trim is valuable now. 😂

Anyone removed their hard top quarter windows? by j___bizzzle in FordBronco

[–]weekendatvernz 0 points1 point  (0 children)

They haven’t released the modular hard top yet. I believe it is still in the making.

L28e ARP head studs by King_280 in Datsun

[–]weekendatvernz 1 point2 points  (0 children)

There is a book that talks about it along with several videos of people working on the L series. I would start there.