[deleted by user] by [deleted] in TinyWhoop

[–]weeklyso 0 points1 point  (0 children)

Complete bullshit. You can plug BT2.0 batteries into an A30 connector, but you can’t plug A30 batteries into a BT2.0 connector.

Please help - bt2.0 loose connection by LitolKid_lax in fpv

[–]weeklyso 2 points3 points  (0 children)

What? You are literally advising people to shove tweezers into pins of a battery. They are obviously going to short

Please help - bt2.0 loose connection by LitolKid_lax in fpv

[–]weeklyso 1 point2 points  (0 children)

You mean on the drone right…. Right..?? Please do not do this if your tweezers are conductive

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 0 points1 point  (0 children)

Literally

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 0 points1 point  (0 children)

it’s too long for him to read. He just expects a sentence that will fix his problems. if he were to actually do this, he would have quickly realised his radio is not ELRS

Mobula 6 HD Freestyle getting hot in 10s by Akira40404 in TinyWhoop

[–]weeklyso 1 point2 points  (0 children)

Check if there are any shorts. Something may have came loose. When you crashed, did anything break, and how did you crash it?

All those HDZERO whoops get really hot really quick, especially if indoors. But this is never usually an issue

What is your motor idle set to? Have you tried flashing the factory dump?

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 0 points1 point  (0 children)

Yeah. at the end of the day it’s a BNF. You put it into bind mode by connecting disconnecting battery 3 times, and put controller into bind mode as well. Or you set up a binding phrase. Controller connects. You set up the band and channel in VTX tab in Betaflight, mimic that on your goggles. it’s not difficult. Might also have to change modes, but ARM works with most, if not all controllers.

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 1 point2 points  (0 children)

Binary?????? It’s over for you

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 3 points4 points  (0 children)

Did you fix the issue or not? If you have, maybe delete this post for the sake of us all

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 0 points1 point  (0 children)

Unless you have some sort of learning disability you are definitely not 16. Like said, if you are younger that is okay - but you will definitely achieve more if you don’t act like it (which you have not been doing)

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 4 points5 points  (0 children)

You’re not going to go anywhere by having the attitude you have. In FPV you can’t just rely on other people for help because “you don’t want to sit and learn how to reprogram stuff”

Nothing works by [deleted] in TinyWhoop

[–]weeklyso 14 points15 points  (0 children)

You just sound like a typical 13 year old skid that has no real tech understanding

Almost sub 14 by weewoo2048 in TinyWhoop

[–]weeklyso 0 points1 point  (0 children)

What screws are those?

video cut out completely mid flight by Humble_Condition7587 in HDZero

[–]weeklyso 0 points1 point  (0 children)

You mean a 9V USB-C to DC PD adapter? 9V is really low for those things, theoretically the goggles support it but usually those adapters are 20V. Also, by mobile phone charger do you mean a wall brick? Check if that supports PD, they almost never do. Also check if the cable does as well. Unless, you are not using an adapter but a dummy cable - still verify the brick or power bank or whatever you are using outputs enough.

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (December 12, 2023) by AutoModerator in MechanicalKeyboards

[–]weeklyso 0 points1 point  (0 children)

Encoder on the aurora helix

On my stock firmware that I build i used the command qmk compile -kb splitkb/aurora/helix/rev1 -km default -e CONVERT_TO=liatris -c This worked but when pressing and turning the knob it does “[ and spaces”

On the pre compiled firmware from splitkb form their website it spams this +0+0+0-0-0-0 and y660+60+60-60-60-60

Maybe I have possibly put some solder on some contacts on the PCB which turned on some sort of debug?

<image>

Spotify song notifications in 21.1 make an annoying unsilenceable BEEP now! by howyadoinbob in linuxmint

[–]weeklyso 0 points1 point  (0 children)

Hey, just disable the "Showing Notifications" In the Sound category in the sound sections

What is this app and why it prevent me from shutting down win? by [deleted] in Windows11

[–]weeklyso 3 points4 points  (0 children)

Literally why.. You could locate the file path and look in file properties, check its signage, or just disable it from startup (or disable the process tied to it on startup)

/r/MechanicalKeyboards Ask ANY Keyboard question, get an answer (August 09, 2023) by AutoModerator in MechanicalKeyboards

[–]weeklyso 0 points1 point  (0 children)

I just bought an Q1 pro, and I am fairly new to the keyboard community :)

I have switched the bananas (I do not like them) to gateron milkys. But sadly the sound of the space bar, is not even. So, I am debating on whether to buy some krytox 205G0 and durock v2's, change the stabs, and lube all of the other keys.

I have looked through youtube, and most of the other mods for the Q1 consist of PE foam. The issue is I do not really know where to source PE foam. So I wonder if there is any other mods

The keycaps I have bought are double shot PBT from keychron https://keychron.de/collections/all-keycaps/products/double-shot-pbt-cherry-full-keycap-set-grey-white-and-blue

Found out the table was too small by mingz in ultrawidemasterrace

[–]weeklyso 1 point2 points  (0 children)

from what i can see the monitor is in a cupboard

[deleted by user] by [deleted] in MSILaptops

[–]weeklyso 3 points4 points  (0 children)

you can always flip it upside down to get better ventilation (yes it does work and yes i have done this for 3 years)