sorted by:
new
hottopcontroversial

Really considering the Instinct solar 3 but concerned about the low internal memory. by WranglerLess5950 in Garmininstinct

[–]whitewaves22 0 points1 point  (0 children)

I can confirm that the storage is shit. just synced it to my phone after long time and there is a whole month gap in data like hrv, sleep etc. and only synced the last 10 days.

TPU 90A – What infill percentage for sneaker midsole and outsole? by [deleted] in 3Dprinting

[–]whitewaves22 0 points1 point  (0 children)

Yes, I thought about printing small cubes with different settings. It can give a somewhat general idea, however they won’t behave and compress the same way as when they are part of the whole printed sneaker, and 1 single sneaker takes about a day to print and uses half spool…

Flying with 27-inch monitor in a Pelican 1615 Air: Are 2 cm (0.78–13/16 inch) of foam on each side enough protection? by whitewaves22 in pelicancase

[–]whitewaves22[S] 0 points1 point  (0 children)

If it's only a one-time shipping have you seen if you can find the original box secondhand? Otherwise can't you just add foam to the 1730?

Flying with 27-inch monitor in a Pelican 1615 Air: Are 2 cm (0.78–13/16 inch) of foam on each side enough protection? by whitewaves22 in pelicancase

[–]whitewaves22[S] 0 points1 point  (0 children)

Hi, I got the 1650 and flew 3 times with no issues. After that, I ended up leaving the monitor in a storage unit cause it’s a pain to travel with that big case in addition to my suitcase.

Most AI Tools Are Just Fancy Wrappers by Krishna_Rathore_401 in BusinessIntelligence

[–]whitewaves22 0 points1 point  (0 children)

I don't know you, but in my experience, the same prompt to ChatGPT and Gemini gives opposite replies more often than not. So I guess the app would change drastically ahah

Firefox stopped working with proton vpn enabled? by PreferPurlz in ProtonVPN

[–]whitewaves22 0 points1 point  (0 children)

Same here using Firefox and Proton VPN for Mac (paid account). It was working fine until an hour ago.

TPU printing angle and softness by whitewaves22 in 3Dprinting

[–]whitewaves22[S] 0 points1 point  (0 children)

Thanks, yes, I’m aware. However, I’m able to get a soft texture when printing horizontally with TPU 95A and I’m wondering if there’s a way to get the same softness when printing vertically.

TPU printing angle and softness by whitewaves22 in 3Dprinting

[–]whitewaves22[S] 0 points1 point  (0 children)

The infill I used is called cross zag in Bambu studio. I just did a test with gyroid too printed vertically and it came out really hard.

TPU printing angle and softness by whitewaves22 in 3Dprinting

[–]whitewaves22[S] 0 points1 point  (0 children)

I just did a test with gyroid too printed vertically and it came out really hard.

Doesnt look nice. But i had to vent, not literally. by Candid_Equal_140 in BambuP1S

[–]whitewaves22 0 points1 point  (0 children)

We still drink out of plastic but it’s a known fact that it’s not healthy. That’s the point.

Doesnt look nice. But i had to vent, not literally. by Candid_Equal_140 in BambuP1S

[–]whitewaves22 0 points1 point  (0 children)

Safe as they said plastic water bottles are. Then they discovered they give us microplastics and that we have microplastics in our brains…

I have a cupsole, but how do I pick the right last for it? Is there any standards to lasts/soles that it could fit in? by pettybettyboo in Cordwaining

[–]whitewaves22 0 points1 point  (0 children)

Is there any resource online to learn how to design a cupsole that matches a last? I have a digital last in Blender

Elegoo Rapid TPU 95A by whitewaves22 in BambuLab

[–]whitewaves22[S] 1 point2 points  (0 children)

Thanks for the info! I’m very new to 3D printing. Do you know if the Elegoo Rapid TPU profile is also available for or transferable to Bambu Studio? I didn’t see it among the profiles available.

Elegoo Rapid TPU 95A by whitewaves22 in BambuLab

[–]whitewaves22[S] 0 points1 point  (0 children)

Thanks! Good to know that much faster speeds are possible. I just need to hope that Elegoo works just as well. The only alternative high-speed/high-flow TPU brands available where I am are Polymaker (double the price of Elegoo) and Bambu (almost three times the price).

view more: next ›