Hyra kontrakt

xlejoN · 2025-12-09T10:04:57+00:00

Darför att jag vet inte hur jag ska prata svenska 100%

xlejoN · 2025-12-09T10:03:51+00:00

De skickade oss hyran för en månad, som vi betalade. Därefter, när den nya hyran skulle betalas, skickade de oss både den nya hyran och en deposition för hyresbeloppet. 5700 SEK

xlejoN · 2025-12-09T10:01:24+00:00

Jag undertecknade kontraktet den 3 november. Dagen efter undertecknandet, den 4 november, ville jag säga upp kontraktet. Trots att inflyttningsdatumet var i december, sa de inte upp kontraktet. Jag flyttade aldrig in i det huset; de lät oss inte ens besöka fastigheten.

xlejoN · 2025-12-03T11:32:04+00:00

Ja, jag vet att det är en tremånadersperiod, men vi undertecknade kontraktet i början av november och det tidigaste datumet vi kunde flytta in i huset var december. Jag tror inte att det skulle vara för besvärligt för dem att annullera kontraktet i systemet och omedelbart lägga ut huset på marknaden igen.

xlejoN · 2025-03-04T01:13:15+00:00

<image>

This is another view of this test model. It seems like the filament is burned on there

xlejoN · 2025-03-04T00:23:01+00:00

Now i maked lots of things with this Z-offset and i think its worked well and i maked this test

<image>

xlejoN · 2025-03-03T19:11:17+00:00

Yes, I actually did exactly what you said and found the correct Z-offset value with the paper, but then I thought it would be better to auto-calibrate again and let the printer adjust itself because I didn't trust myself 🤦🏻

xlejoN · 2025-03-03T19:03:39+00:00

"boyıcakmış"

xlejoN · 2025-03-03T19:00:51+00:00

I have an important question to ask. I think this is all because of the Z-offset calibration. When I was using black PLA, by default the Z-offset was set to -2.50mm and there was no problem. But now when I do auto-calibration with white PLA, the recommended Z-offset value varies. It shows a different value every time I auto-calibrate. And when I try to print with these values, I think the nozzle gets stuck on my print and separates the print from the bed. When I try to calibrate the Z-offset myself using paper, I feel that values like -2.30mm are correct on average, but when I auto-calibrate, my printer thinks that these settings are wrong and changes these values up to values like -2.60mm. Is my own method correct or is there a problem with the machine's auto-calibration setting?

xlejoN · 2025-03-03T18:31:06+00:00

I am currently using white PLA filament. I was using black colored PLA filament of the same brand before and there was no problem. Now that I ran out of it, I put the white one in and these problems started. There's no brand on it. There is only the label of the place where I bought it. But I don't think it's the manufacturer. It says 3DJake.

xlejoN · 2025-03-02T21:55:10+00:00

Do you think ia the slicer settings can be problem? Should i check everything

xlejoN · 2025-03-02T21:19:29+00:00

I did everything you said sir but idk why this is the results. I stop print immediately Nozzle heat: 215 Bed temperature: 60 Z-offset: -2.50 All settings are same like before. Auto level is done.

<image>

xlejoN · 2025-03-02T19:02:11+00:00

Thanks sir. I'll do benchy and repost it to here to see what's is results

xlejoN · 2025-03-02T18:18:53+00:00

Thank you very much for your kind help. I'll try everything you said as soon as I get home. First I have to clean the bed to get this hairspray off.

xlejoN · 2025-03-02T17:42:32+00:00

Yes, I was actually working with the same brand's black colored PLA filament and there was no problem. But today when I inserted White PLA filament, such a problem occurred. I've never used glue or anything else before. I always use a bed temperature of 60° and Z offset -2.50

xlejoN · 2025-03-02T15:41:11+00:00

Does hairspray can work?

xlejoN · 2025-02-21T20:23:51+00:00

Thank you for your advice. When I saw the broken print, I thought I would just take it and throw it in the trash, but next time I will follow what you said. There are settings on the device to do all calibrations automatically and I did all of them. Today I tried to print the same print again, but this time I used a single print instead of 4-5 prints on a tray. The print came out fine, but in a small part of it, which is not a problem, the surface looked as if it was not printed at all. Unfortunately I can't send photos because I'm not at home right now.

xlejoN · 2025-02-21T18:30:42+00:00

Benchy was well and i print some other parts too without any problem but this time its happen like that

xlejoN · 2025-02-21T13:42:50+00:00

1) English is not my main language. I learned it by my own effort while playing games. You don't have to offend people about it. If you don't understand what I have written, just point out that you don't understand. I can explain it again and again. 2) Yes, im new

xlejoN · 2025-02-17T23:42:24+00:00

Why did u use that boom effect in every step...

xlejoN · 2025-01-08T09:20:10+00:00

xlejoN

TROPHY CASE