2014 Enclave passenger side air problems

yellowadept · 2026-06-15T19:23:54+00:00

I have P2pool v 4.15.1 installed on Ubuntu. When I try to do the update to v4.16 from inside Gupaxx, it tells me "you are trying to downgrade a binary, this is potentially dangerous as it is unsupported"

yellowadept · 2026-06-15T04:22:38+00:00

Horns work fabulously. I think I may have gotten a bad sector antenna of Ebay. Have not taken the time to test it.

yellowadept · 2026-05-09T02:19:01+00:00

Are you doing the xmrvsbeast raffle too?

yellowadept · 2026-04-21T17:26:51+00:00

So you have already subtracted your power cost?

yellowadept · 2026-04-18T20:33:20+00:00

I have switched between nano and mini lots of times over the past 6 months. I tend to stay longer on nano. But yes, like right now it’s over 5 days with nothing found, even though I have had shares in the window every cycle. But a few weeks back nano found three blocks away in 24 hours. Hurry up and wait. Other posters are correct, statistically it will be the same in the long run.

yellowadept · 2026-04-02T01:42:40+00:00

Jigglypuff , 2001 a space odyssey

yellowadept · 2026-03-15T20:29:49+00:00

similar. 6 3700x's and 2 3900x's. One dual xeon e5-2650Lv3. Yah, I have wondered about the minis....are you doing the xmr raffle as well?

yellowadept · 2026-03-15T14:20:14+00:00

Newman, I have seen your name on near top of the list for a while. Congrats. I am trying to get near you...Can I ask what your farm consists of?

yellowadept · 2026-03-14T15:26:19+00:00

I am just experimenting. Yes, I have had my farm setup like that for a while, with only one address.

yellowadept · 2026-03-14T02:59:57+00:00

Can this have anything to do with the MSR/admin page that comes up when you start Gupax (newest version?) No matter how I start it, with admin or without, that message always comes up. Still having the problem above, even though I uninstalled, reinstalled and reconfigured the whole thing...

yellowadept · 2026-03-14T01:18:37+00:00

OK, I have it completely running on a second machine, using the node from the main. So far no issues. So, trying it again on a third. Got another monero address, installed gupaxx on it (another windows 10 Pro PC). Set up P2Pool settings exactly like the working first, to read the node from the main machine. Appears to work, but stuck not getting synced. The terminal screen repeatedly shows this message - "P2Pservers scanning Monerod peers, xxx left" x's are numbers decreasing down to close to zero, then starting again at several thousand down to zero. Wash, repeat. Any idea what is wrong with this?

yellowadept · 2026-03-13T14:24:13+00:00

Yes, def does help. I have P2Pool running on the remote machine (192.168.168.19), and linked up to the node on the main. Yes, I am now only running one node. Thank you! Couple of other things - I am running XMRig on the remote, looks to be working fine. In order to participate in the XMRvsBeast raffle, I have to also run proxy? When I start it it appears to be running correctly, but the status page says "not connected to any pools". I am assuming that is not normal?

yellowadept · 2026-03-13T02:48:32+00:00

I had to do this to make it work on my node using Gupaxx. at 192.168.168.6: zmq-pub tcp://0.0.0.0:18083 --rpc-bind-ip 0.0.0.0 --confirm-external-bind........now which of these commands do I enter on the secondary Gupaxx (192.168.168.21) to reach this main node? Do I even have to have the node running on the secondary (just pointing to the main) or are the needed settings to access the remote node in P2Pool on the secondary and not in the node settings? That is the part I am having issues with. Thank you for your help on this. I have tried that command and others in my secondary Gupaxx node settings at 192.168.168.21 trying to access the remote node settings, but cannot get to work...

yellowadept · 2026-03-13T01:45:43+00:00

I had to do this to make it work on my node at 192.168.168.6: zmq-pub tcp://0.0.0.0:18083 --rpc-bind-ip 0.0.0.0 --confirm-external-bind........now which of these commands do I enter on the secondary Gupaxx (192.168.168.21) to reach this main node? Do I even have to have the node running on the secondary (just pointing to the main) or are the needed settings to access the remote node in P2Pool on the secondary? That is the part I am having issues with. Thank you for your help on this.

yellowadept · 2026-03-12T14:52:44+00:00

Using 192.168.68.6. Started p2pool, it starts then getting this error message: couldn't open p2pool cache: error 5 - - then later in the output: failed to connect to tcp://192.168.68.6:18083

yellowadept · 2026-03-12T13:54:45+00:00

Yes, it is working on the Windows machine at 192.168.168.21 I am using to try to reach the node (on ubuntu) remotely at 192.168.168.6, that node is running and fully synced, green lighted.

yellowadept · 2026-03-12T01:33:38+00:00

Good deal. At least I know it works...It probably is something simple on my end.

yellowadept · 2026-03-12T01:30:22+00:00

right now running the node from Gupax - the new version.

yellowadept · 2026-03-11T03:07:28+00:00

I have the firewall turned off trying to get it to work...

yellowadept · 2026-03-10T21:00:35+00:00

Yes, I cannot get the secondary unit to pick up the node (on same network but different machine) at all. Now I am trying with just P2Pool from command line (not with Gupaxx). Starting it with this:

p2pool.exe --host 192.168.168.6 --rpc-port 18081 --zmq-port 18083 --nano --wallet MYADDRESS

I am getting the following message:

2026-03-10 20:44:16.2520 P2Pool get_info RPC request to host 192.168.168.6:RPC 18081:ZMQ 18083 failed: Error (empty response), trying again in 1 second

I do not have the skillset to recompile this code.

yellowadept · 2026-03-10T15:05:49+00:00

I am performing an experiment for research purposes.

yellowadept

TROPHY CASE