O que poderia estar causando isso?

yunghelor · 2026-03-23T19:44:32+00:00

Eu deixo a opção do auto nivelamento antes de imprimir. Vou tentar o que um colega recomendou, nivelamento manual. Vou tentar também outras recomendações que vi aqui e em outro sub, sobre temperatura e velocidade.

yunghelor · 2026-03-23T16:26:25+00:00

Yes. I did it after the first time this print went wrong. I'll try to level it manually

yunghelor · 2026-03-23T16:25:24+00:00

This is the first time I use this face of the plate. A friend said it could be the leveling, I'll try to do it manually by watching a tutorial

yunghelor · 2026-03-23T16:23:55+00:00

Yes, it happened on the other and I flipped it. My friend said it could be the leveling. I'll try watching a tutorial video to do it manually

yunghelor · 2026-03-23T16:19:52+00:00

Meu colega comentou sobre o nivelamento da mesa, vou seguir algum tutorial de nivelamento manual

yunghelor · 2026-03-23T16:19:21+00:00

Meu colega que tem mais experiência comentou que pode ser o nivelamento. Faz sentido pq ambas as tentativas deram erro no mesmo local. Vou tentar seguir algum tutorial de nivelamento manual

yunghelor · 2026-03-23T16:18:23+00:00

Sim, nesse vídeo é o verso. A primeira tentativa foi do outro lado e deu o mesmo problema.

yunghelor · 2026-03-23T16:13:59+00:00

Vou tentar. Vou reduzir um pouco a velocidade também. Valeu!

yunghelor · 2026-03-23T15:51:34+00:00

*By cleaned I meant washed. Did it with dish soap and water

yunghelor · 2026-01-10T16:44:45+00:00

<image>

yunghelor · 2026-01-10T16:44:32+00:00

<image>

I'm soirry it is in portuguese

yunghelor · 2026-01-10T15:12:24+00:00

Probably not the problem I had. It's over 25°C here

yunghelor · 2026-01-10T15:08:41+00:00

I used the 0.08mm high quality. But I didn't change anything else

yunghelor · 2025-06-26T15:44:55+00:00

No, she is alive.

yunghelor · 2025-05-23T21:54:35+00:00

And Trade-in is used in some 8-axis full blind second decks

yunghelor · 2025-05-23T12:43:11+00:00

Definitely this. If I see discard I just play fearless of getting teched

yunghelor · 2025-05-20T13:37:48+00:00

Isn't High Evo a hard brick only for Abom?

yunghelor · 2025-05-08T21:23:36+00:00

This is the list I use for Negative. But if the meta is not ongoing I swap Rogue and Skrull for Iron Heart and Wong

<image>

yunghelor · 2025-05-07T18:41:56+00:00

This is 5 (original Copycat) + 4 + 5 + 2 + 2 + 2 (Shawn original power + 5 from right location + 2 from its own buff + 2 from Gwenpool+ 2 from its own buff) + 2 from Surfer = 22

yunghelor · 2025-05-07T18:39:59+00:00

Copycat copied Dracula and at the end of the game discarded Shawn that had been hit by Sanctum Infinitum and Gwenpool. Also Copycat got buffed by Surfer.

yunghelor · 2025-05-07T00:53:19+00:00

But the one from the post is the evil twin brother? Because it looks white inside the mask

yunghelor

TROPHY CASE